2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. A125680
    Loosen the radiator drain cock plug.

  1. Remove the reserve tank cap and drain the coolant.

  1. Tighten the radiator drain cock plug.

    A128304E01


3. REMOVE ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Disengage the 4 pins and remove engine cover No. 1.


4. REMOVE GLOW PLUG NO. 1 CONNECTOR

  1. A098269
    Remove the 5 screw grommets.

  1. A098270
    Remove the nut and disconnect the glow terminal.

  1. Remove the 4 nuts and glow plug connector No. 1.


5. SEPARATE OIL LEVEL GAGE GUIDE

A125673
  1. Remove the bolt and separate the oil level gage guide.


6. REMOVE EGR COOLER ASSEMBLY

  1. A125674
    Disconnect the 2 water by-pass hoses.

  1. Remove the bolt and 4 nuts, then remove the EGR cooler assembly.

  1. Remove the 2 gaskets.


7. REMOVE VACUUM REGULATING VALVE ASSEMBLY

A125788E01
  1. Disconnect the connector clamp and connector.

  1. Disengage the 2 hose clamps and disconnect the 2 vacuum hoses.

  1. Remove the 3 bolts, then remove the vacuum regulating valve together with the bracket.


8. REMOVE INJECTION PIPE CLAMP NO. 1

A098451
  1. Remove the 2 nuts, then remove injection pipe clamp No. 1.


9. REMOVE INJECTION PIPE CLAMP NO. 2

A098452
  1. Remove the nut, then remove injection pipe clamp No. 2.


10. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 1

A069347E01
  1. Using a spanner (13 mm), hold the injector steadily, and using SST, remove the injection pipe from the injector side.

    SST
    09023-38401  

  1. Using SST, remove the injection pipe from the common rail side.

    SST
    09023-38401  

  1. After removing the injection pipe, cover the common rail with vinyl tape and cover the injector inlet with a vinyl or plastic bag in order to prevent dust and foreign matter from entering.


11. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 2
SST
09023-38401  

HINT:
Perform the same procedure as for injection pipe No. 1.


12. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 3
SST
09023-38401  

HINT:
Perform the same procedure as for injection pipe No. 1.


13. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 4
SST
09023-38401  

HINT:
Perform the same procedure as for injection pipe No. 1.


14. REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

A098453
  1. Remove the 5 retainer springs, then remove the nozzle leakage pipe.


15. REMOVE INJECTOR ASSEMBLY

A098454E01

HINT:
  1. Each injector assembly has its own fuel injection part number. when replacing the injector assembly, store them in the correct order so that they can be returned to their original locations when reassembled.
  2. Arrange the injectors, clamps, washers, bolts and clamp seats in the correct order.

  1. Remove the 4 bolts, 4 washers, 4 nozzle holder clamps and 4 nozzle holder clamp seats.

  1. Disconnect the 4 injector connectors.

  1. Remove the 4 injectors from the cylinder head.

  1. Remove the 4 injection nozzle seats from the injector or cylinder head.

    NOTICE:
    When removing the injector, check that the injector nozzle seat is either attached to the injector, or remains in the cylinder head.

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →