2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL COMMON RAIL ASSEMBLY

A098485
  1. Install the common rail assembly

  1. Connect the fuel hose.

  1. Install the common rail with 2 bolts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 in.*lbf }


2. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

A125732E01

NOTICE:
  1. When replacing the common rail, the fuel inlet pipe must also be replaced.
  2. Replace the fuel inlet pipe with a new one when the fuel inlet pipe has been removed and reinstalled more than 5 times.

  1. Temporarily install the fuel inlet pipe onto the supply pump and common rail.

    NOTICE:
    Install the pipe and union nut vertically, not at a tilt.

  1. A098463E01
    Using SST, tighten the fuel inlet pipe union nut of the fuel inlet pipe on the common rail side.
    SST
    09023-38401  

    Torque:
    With SST:
    23 N*m{ 235 kgf*cm , 17 in.*lbf }
    Without SST:
    25 N*m{ 255 kgf*cm , 18 in.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the fuel inlet pipe has been reassembled, check that the used pipe has no deflection and is installed properly.
      If it has deflection or could not be installed properly, replace the used pipe with a new one.

  1. A128765E01
    Using a spanner (17 mm), hold the supply pump steady, and using SST, tighten the fuel inlet pipe union nut of the fuel inlet pipe on the supply pump side.
    SST
    09023-38401  

    Torque:
    With SST:
    23 N*m{ 235 kgf*cm , 17 in.*lbf }
    Without SST:
    25 N*m{ 255 kgf*cm , 18 in.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the fuel inlet pipe has been reassembled, check that the used pipe has no deflection and is installed properly.
      If it has deflection or could not be installed properly, replace the used pipe with a new one.


3. INSTALL INJECTION PIPE SUB-ASSEMBLY NO. 1

A125732E01

CAUTION:
  1. When replacing the common rail, the injection pipes must also be replaced.
  2. Replace the injection pipe with a new one when the injection pipe has been removed and reinstalled more than 5 times.

  1. Temporarily install the 4 injection pipes onto the injector and common rail.

    NOTICE:
    Install the pipe and union nut vertically, not at a tilt.

  1. A128766E01
    Using SST, tighten the injection pipe union nut of the injection pipe on the common rail side.
    SST
    09023-38401  

    Torque:
    With SST:
    23 N*m{ 235 kgf*cm , 17 in.*lbf }
    Without SST:
    25 N*m{ 255 kgf*cm , 18 in.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the fuel inlet pipe has been reassembled, check that the used pipe has no deflection and is installed properly.
      If it has deflection or could not be installed properly, replace the used pipe with a new one.

  1. A098458E01
    Using a spanner (13 mm), hold the injector steady, and using SST, tighten the injection pipe union nut of the injection pipe with a new one.
    SST
    09023-38401  

    Torque:
    With SST:
    23 N*m{ 235 kgf*cm , 17 in.*lbf }
    Without SST:
    25 N*m{ 255 kgf*cm , 18 in.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. After the fuel inlet pipe has been reassembled, check that the used pipe has no deflection and is installed properly.
      If it has deflection or could not be installed properly, replace the used pipe with a new one.


4. INSTALL INJECTION PIPE SUB-ASSEMBLY NO. 2
SST
09023-38401  

HINT:
Perform the same procedure as for injection pipe No. 1.


5. INSTALL INJECTION PIPE SUB-ASSEMBLY NO. 3
SST
09023-38401  
Perform the same procedure as for injection pipe No. 1.

6. INSTALL INJECTION PIPE SUB-ASSEMBLY NO. 4
SST
09023-38401  
Perform the same procedure as for injection pipe No. 1.

7. INSTALL INJECTION PIPE CLAMP NO. 2

8. INSTALL INJECTION PIPE CLAMP NO. 1

9. INSTALL VACUUM REGULATING VALVE ASSEMBLY

  1. A125788
    Install the vacuum regulating valve with the 3 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 in.*lbf }

  1. Connect the vacuum regulating valve connector and 2 vacuum hoses.


10. INSTALL EGR COOLER ASSEMBLY

  1. A125674E01
    Install 2 new gaskets.

  1. Temporarily install the EGR cooler assembly with the bolt and 4 nuts, in the order described below.

    1. Tighten bolt B.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    2. Tighten the 2 A nuts.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    3. Tighten the 2 C nuts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 water by-pass hoses.


11. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE

A126500E01
  1. Align the matchmarks of air cleaner hose No. 1 and turbocharger, and connect air cleaner hose No. 1 to the turbocharger and fasten air cleaner hose clamp No. 1.

    NOTICE:
    Make sure that the hose clamp is at the correct angle when installing it.

  1. A098276E01
    Connect the ventilation hose to the cylinder head cover.

    NOTICE:
    Make sure that the hose clamp is at the correct angle when installing it.

  1. Install the air cleaner cap onto the air cleaner case, then hang the 2 hook clamps.

  1. A118837
    Fit the wire harness into the air cleaner cap.

  1. Engage the 2 wire harness clamps.

  1. Connect the mass air flow meter connector.


12. INSTALL OIL LEVEL GAGE GUIDE

A125673
  1. Install the bolt and the oil level gauge guide.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


14. ADD ENGINE COOLANT

A128306E01
  1. Remove air bleed valve A.

  1. A128305
    Fill the cooling system with coolant up to line B.

    Capacity:
    4.7 liters (5.0 US qts, 4.1 lmp. qts)

    HINT:
    1. Use of improper coolant may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. A128306E01
    Tighten air bleed valve A.

  1. Install the radiator cap.

  1. Warm up the engine.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

  1. Run the engine at 3,000 rpm for 5 seconds and idling for 45 seconds alternately.

  1. Do the above operation for 7 minutes or more.

  1. After the engine cools down, check that the coolant level is between LOW and FULL lines.


15. CHECK ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A128299
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.


16. CHECK FOR FUEL LEAKAGE

A127178E01
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test.

    HINT:
    1. Fuel pressure inside common rail pressurized to 135 MPa and engine speed increased to 2,000 rpm when ON selected.
    2. Above conditions preserved while test ON.


17. CHECK FOR ENGINE COOLANT LEAKAGE

18. INSTALL ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Engage the 4 pins and install engine cover No. 1.

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →