2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. A125680
    Loosen the radiator drain cock plug.

  1. Remove the reserve tank cap and drain the coolant.

  1. Tighten the radiator drain cock plug.

    A128304E01


3. REMOVE ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Disengage the 4 pins and remove engine cover No. 1.


4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE

A118837
  1. Disconnect the mass air flow meter connector.

  1. Disengage the 2 wire harness clamps, and separate the wire harness from the air cleaner cap.

  1. A118856
    Unfasten the 2 lock clamps, and separate the air cleaner cap.

  1. Disconnect the ventilation hose from the cylinder head cover.

  1. Disconnect the air cleaner hose from the turbocharger, and remove the air cleaner with hose.


5. SEPARATE OIL LEVEL GAGE GUIDE

A125673
  1. Remove the bolt and separate the oil level gage guide.


6. REMOVE EGR COOLER ASSEMBLY

  1. A125674
    Disconnect the 2 water by-pass hoses.

  1. Remove the bolt and 4 nuts, then remove the EGR cooler assembly.

  1. Remove the 2 gaskets.


7. REMOVE VACUUM REGULATING VALVE ASSEMBLY

A125788E01
  1. Disconnect the connector clamp and connector.

  1. Disengage the 2 hose clamps and disconnect the 2 vacuum hoses.

  1. Remove the 3 bolts, then remove the vacuum regulating valve together with the bracket.


8. REMOVE INJECTION PIPE CLAMP NO. 1

9. REMOVE INJECTION PIPE CLAMP NO. 2

10. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 1

A069347E01
  1. Using a spanner (13 mm), hold the injector steady, and using SST, remove the injection pipe from the injector side.

    SST
    09023-38401  

  1. Using SST, remove the injection pipe from the common rail side.

    SST
    09023-38401  

  1. After removing the injection pipe, cover the common rail with vinyl tape and cover the injector inlet with a vinyl or plastic bag in order to prevent dust and foreign matter from entering.


11. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 2
SST
09023-38401  

HINT:
Perform the same procedure as for injection pipe No. 1.


12. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 3
SST
09023-38401  

HINT:
Perform the same procedure as for injection pipe No. 1.


13. REMOVE INJECTION PIPE SUB-ASSEMBLY NO. 4
SST
09023-38401  

HINT:
Perform the same procedure as for injection pipe No. 1.


14. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

A098482E01
  1. Using a spanner (17 mm), hold the supply pump steadily, and using SST, remove the fuel inlet pipe from the supply pump side.

    SST
    09023-38401  

  1. A098483E01
    Using SST, remove the fuel inlet pipe from the common rail side.
    SST
    09023-38401  

  1. After removing the fuel inlet pipe, cover the common rail with vinyl tape and cover the injector inlet with a vinyl or plastic bag in order to prevent dust and foreign matter from entering.


15. REMOVE COMMON RAIL ASSEMBLY

A098485
SST
09023-38401  
  1. Disconnect the 2 connectors.

  1. Disconnect the fuel hose.

  1. Remove the 2 bolts and common rail.

    NOTICE:
    Do not remove the fuel pressure sensor or fuel pressure regulator.

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →