2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FUEL FILTER ELEMENT

A125685
  1. Check and clean the fuel filter installation surface.

  1. Apply fuel to the gasket of a new fuel filter element.

  1. Lightly screw the fuel filter element into place, and tighten it until the gasket comes into contact with the seat.

  1. Tighten it an additional 3/4 turn by hand.


2. INSTALL LEVEL WARNING SWITCH

A128824E01
  1. Install a new O-ring onto the level warning switch.

  1. Apply fuel to the O-ring of the level warning switch.

  1. Install the level warning switch onto the fuel filter by hand.


3. INSTALL FUEL FILTER ASSEMBLY

A125684
  1. Install the fuel filter with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.

  1. Connect the 4 hoses to the fuel filter.

  1. Carry out priming work until the hand pump feels hard when pushed since filling the fuel filter with fuel is required after replacement of the fuel filter.


4. INSTALL COWL TOP PANEL OUTER

A126332
  1. Install the cowl top panel outer with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Install the wire harness.


5. INSTALL COWL TO REGISTER DUCT SUB-ASSEMBLY NO. 2

6. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


7. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


8. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


9. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


10. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


11. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


12. INSTALL FRONT WIPER ARM AND BLADE SUB-ASSEMBLY LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


13. INSTALL FRONT WIPER ARM AND BLADE SUB-ASSEMBLY RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


14. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


16. CHECK FUEL LEAK

A127178E01
  1. Connect an intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Active Test.

    HINT:
    1. Fuel pressure inside common rail pressurized to 135 MPa and engine speed increased to 2,000 rpm when ON selected.
    2. Above conditions preserved while test ON.

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →