2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL EGR VALVE ASSEMBLY

  1. A125675
    Install a new gaskets.

  1. Install the EGR valve assembly with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the EGR valve connector and hose.


2. INSTALL EGR COOLER ASSEMBLY

  1. A125674E01
    Install 2 new gaskets.

  1. Temporarily install the EGR cooler assembly with the bolt and 4 nuts, in the order described below.

    1. Tighten bolt B.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    2. Tighten the 2 A nuts.

      Torque:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    3. Tighten the 2 C nuts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 water by-pass hoses.


3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


4. ADD ENGINE COOLANT

A128306E01
  1. Remove air bleed valve A.

  1. A128305
    Fill the cooling system with coolant up to line B.

    Capacity:
    4.7 liters (5.0 US qts, 4.1 lmp. qts)

    HINT:
    1. Use of improper coolant may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. A128306E01
    Tighten air bleed valve A.

  1. Install the radiator cap.

  1. Warm up the engine.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

  1. Run the engine at 3,000 rpm for 5 seconds and idling for 45 seconds alternately.

  1. Do the above operation for 7 minutes or more.

  1. After the engine cools down, check that the coolant level is between LOW and FULL lines.


5. CHECK ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A128299
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.


6. CHECK FOR EXHAUST GAS LEAKAGE

7. INSTALL ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Engage the 4 pins and install engine cover No. 1.

← INSPECTION (from Nov 2005)ON-VEHICLE INSPECTION (from Nov 2005) →