2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL OIL PUMP SEAL

  1. A069812E01
    Using SST and a hammer, tap in the new oil seal until its surface is flush with the oil pump edge.
    SST
    09223-22010  

    NOTICE:
    Tap in the oil seal vertically.

  1. Apply MP grease to a new oil seal lip.

    NOTICE:
    Keep the lip free of foreign objects.


2. INSTALL OIL PUMP ASSEMBLY

  1. A099119
    Install 2 new O-rings onto the 2 portions as shown in the illustration.

  1. Apply seal packing to the engine body and oil pump as shown in the illustration below.

    Seal packing:
    Part No. 08826-00100 or equivalent for Water pump
    Part No. 08826-00080 or equivalent for othes

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes, and tighten the bolts within 15 minutes of applying seal packing.


    A125840E01

  1. A069333
    Align the keyway of the oil pump drive rotor with the rectangular portion of the crankshaft, then slide the oil pump into place.

  1. A099117E02
    Install the oil pump assembly with the 16 bolts and nut as shown in the illustration.

    Torque:
    Bolt A:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    Bolt B:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    Bolt C:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    Bolt D:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    Nut:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. Be careful not to let the chain come into contact with the seal packing when installing the oil pump.
    2. Install the engine mounting bracket RH and water pump within 15 minutes of installing the oil pump.

    HINT:
    The bolt lengths are as follows.
    Bolt A: 20 mm (0.79 in.)
    Bolt B: 30 mm (1.18 in.)
    Bolt C: 35 mm (1.38 in.)
    Bolt D (double ended bolt): 20 and 14 mm (0.79 and 0.55 in.)


3. INSTALL TIMING CHAIN COVER NO.2

A069329
  1. Install the timing cover No. 2 with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


4. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

A125792
  1. Install the engine mounting bracket with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 in.*lbf }


5. INSTALL WATER PUMP ASSEMBLY

  1. A099105
    Install a new gasket and the water pump with the 3 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


6. INSTALL WATER PUMP PULLEY

  1. A099104E01
    Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts to the specified torque.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }


7. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

A125676E01
  1. Install the engine mounting insulator RH with the 7 bolts and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for bolt A
    88 N*m{ 897 kgf*cm , 65 ft.*lbf } for bolt B
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for nut C
    20 N*m{ 199 kgf*cm , 14 ft.*lbf } for bolt D


8. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY

A099115
  1. Align the key with the key groove of the crankshaft damper, and slide the crankshaft damper to the crankshaft.

  1. Using SST, fix the crankshaft damper.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Tighten the bolt to the specified torque.

    Torque:
    180 N*m{ 1,835 kgf*cm , 133 ft.*lbf }


9. INSTALL VACUUM PUMP ASSEMBLY

10. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

G035854E01
  1. Apply seal packing to the 4 locations as shown in the illustration, then install the cylinder head cover.

    Seal packing:
    Part No. 08826-00080 or the equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    1. Install the cylinder head cover within 3 minutes, and tighten the bolts within 15 minutes of applying the seal packing.

  1. G036743
    Temporarily tighten the cylinder head cover with the 12 bolts.

  1. Tighten the 12 bolts to the specified torque as shown in the illustration.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. A125694
    Install the connector to vacuum reservoir tube with the 2 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. A125689
    Connect the ventilation hose to the cylinder head.

  1. A125693
    Connect the vacuum hose shown in the illustration.

  1. A125692
    Connect the 3 vacuum hoses shown in the illustration.

  1. A125688
    Connect the hose shown in the illustration.

  1. A125691
    Connect the hose shown in the illustration.

  1. G036391E01
    Install the 3 bolts and wire harness clamp shown in the illustration, and connect the engine wire harness.

    Torque:
    Bolt A:
    11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }
    Bolt B:
    13 N*m{ 131 kgf*cm , 9.5 ft.*lbf }

  1. G036390
    Connect the common rail connector.

  1. Install the wire harness with the screw grommet and the nut.

    Torque:
    1.6 N*m{ 16 kgf*cm , 14 in.*lbf }

  1. G036389
    Connect the VSV connector and wire harness clamp shown in the illustration.

  1. A125682
    Connect the wire harness clamp shown in the illustration.

  1. A125690
    Connect the supply pump connector.

  1. G036386
    Connect the injector connector.


11. INSTALL GENERATOR ASSEMBLY

A128376E01
  1. Provisionally install the generator with fixing bolt C.

  1. A128375E01
    Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolt A and nut B, then move the generator toward the cylinder block and tighten bolt B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for Bolt B

  1. A128374
    Install the connector.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.


12. INSTALL FAN AND GENERATOR V BELT
  1. Temporarily install the fan and generator V belt onto each pulley.

    NOTICE:
    1. Before installing the V belt, check each pulley for any kind of liquid and chips.
    1. Check that the ribs of the V belt are correctly fitted into the grooves of the pulleys.


13. ADJUST FAN AND GENERATOR V BELT

  1. A098655
    Insert a bar between the generator and the engine. Pull the bar toward the front of the vehicle and adjust the tension.

  1. A098654E01
    Tighten bolt A, then tighten bolt B.

    Torque:
    Bolt A:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }
    Bolt B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


14. INSPECT FAN AND GENERATOR V BELT

B000543
  1. Check the belt for wear, cracks and other signs of damage.
    If any defects are found, replace the V belt.

    HINT:
    Replace the drive belt if any of the following defects are found:
    1. The belt is worn out and the wire is exposed.
    2. The cracks reach the wire in more than one place.
    3. The belt has pieces missing from the ribs.

  1. B075171E01
    Check that the belt fits properly into the ribbed grooves.

    HINT:
    With your hand, confirm that the belt has not slipped out of the grooves on the bottom of the pulley.


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


16. ADD ENGINE COOLANT

A128306E01
  1. Remove air bleed valve A.

  1. A128305
    Fill the cooling system with coolant up to line B.

    Capacity:
    4.7 liters (5.0 US qts, 4.1 lmp. qts)

    HINT:
    1. Use of improper coolant may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. A128306E01
    Tighten air bleed valve A.

  1. Install the radiator cap.

  1. Warm up the engine.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

  1. Run the engine at 3,000 rpm for 5 seconds and idling for 45 seconds alternately.

  1. Do the above operation for 7 minutes or more.

  1. After the engine cools down, check that the coolant level is between LOW and FULL lines.


17. ADD ENGINE OIL
  1. Fill the engine oil with fresh engine oil.

    Capacity:
    Item
    Capacity
    Drain and refill with oil filter change
    4.3 liters (4.5 US qts, 3.8 lmp. qts)
    Drain and refill without oil filter change
    3.8 liters (4.0 US qts, 3.3 lmp. qts)
    Dry fill
    4.8 liters (5.1 US qts, 4.2 lmp. qts)


18. CHECK ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A128299
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.


19. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine. Then stop the engine, and wait 5 minutes.

  1. Check that the engine oil level is between the 2 marks on the oil level gage.
    If low, check for leakage and top up oil to the upper mark.

    NOTICE:
    Do not add engine oil to above the upper mark.


20. CHECK FOR ENGINE OIL LEAKAGE

21. INSTALL ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Engage the 4 pins and install engine cover No. 1.


22. INSTALL ENGINE UNDER COVER
  1. Provisionally install the engine under cover with the 5 bolts, 4 screws and 2 clips.

  1. Tighten the 4 screws.

  1. Tighten the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


23. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1,050 kgf*cm , 76 in.*lbf }

← REASSEMBLY (from Nov 2005)COMPONENTS (from Nov 2005) →