INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL HEADLIGHT DIMMER SWITCH |
Engage the 3 claws and install the headlight dimmer switch, as shown in the illustration.

Install the headlight dimmer switch with the clamp.

Connect the connector.
| 2. INSTALL WINDSHIELD WIPER SWITCH |
Engage the claw and install the windshield wiper switch.

Connect the 2 connectors.
| 3. INSTALL SPIRAL CABLE SUB-ASSEMBLY (w/o Steering Sensor) |
![]() ![]() |
Check that the ignition switch is turned to off.
Confirm that the negative battery terminal is detached.
- CAUTION:
- Do not begin the operation for at least 90 seconds after the negative battery terminal is detached.
Confirm that the front tires face straight forward.
Confirm that the turn signal switch is in the neutral position.
- NOTICE:
- Perform the operation when the turn signal switch is in the neutral position. Otherwise, the pin of the turn signal will break.
Engage the 3 claws and install the spiral cable.
- NOTICE:
- Pull the lock pin out before installing the steering wheel, when replacing the spiral cable with a new one.
Connect the airbag connector.

Connect the horn connector.
| 4. INSTALL SPIRAL CABLE SUB-ASSEMBLY (w/ Steering Sensor) |
![]() ![]() |
Check that the ignition switch is turned to off.
Confirm that the negative battery terminal is detached.
- CAUTION:
- Do not begin the operation for at least 90 seconds after the negative battery terminal is detached.
Confirm that the front tires face straight forward.
Confirm that the turn signal switch is in the neutral position.
- NOTICE:
- Perform the operation when the turn signal switch is in the neutral position. Otherwise, the pin of the turn signal will break.
Engage the 3 claws and install the spiral cable.
- NOTICE:
- Pull the lock pin out before installing the steering wheel, when replacing the spiral cable with a new one.
Connect the steering connector.

Connect the airbag connector.
Connect the horn connector.
| 5. INSTALL STEERING COLUMN COVER |
w/o Entry and Start System:
Engage the 2 claws and install the steering column cover (upper).

Engage the 2 claws and install the steering column cover (lower).
Tighten the 3 screws.
w/ Entry and Start System:
Engage the 2 claws and install the steering column cover (upper).

Engage the 3 claws and install the steering column cover (lower) and steering column cover support.
Tighten the 3 screws.
| 6. INSTALL STEERING COLUMN COVER SUPPORT (w/ Entry and Start System) |
![]() ![]() |
Disengage the 4 claws and remove the steering column cover support.
| 7. ADJUST SPIRAL CABLE SUB-ASSEMBLY |
Center the spiral cable.

Turn the spiral cable counterclockwise until it locks.
- HINT:
- The spiral cable turns a maximum of approximately 5 times.
Turn the spiral cable 2.5 times clockwise from its locked position and align the center marks.

| 8. INSTALL STEERING WHEEL ASSEMBLY |
Align the matchmarks and install the steering wheel assembly onto the steering column assembly.

Install the nut.
- Torque:
- 50 N*m{ 510 kgf*cm , 37 ft.*lbf }
Connect all connectors to the spiral cable.
| 9. INSTALL STEERING PAD (w/ Steering Pad Switch) |
![]() ![]() |
Connect the horn connector.
Connect the airbag connector.
- NOTICE:
- Securely lock the locking button.
Make sure that the 2 upper claws are aligned and engage them.

Push down the steering pad and engage the lower claw.
- NOTICE:
- If the blind cover is stuck between the steering pad and the steering wheel, push it back to its original position.
| 10. INSTALL STEERING PAD (w/o Steering Pad Switch) |
![]() ![]() |
Connect the horn connector.
Connect the airbag connector.
- NOTICE:
- Securely lock the locking button.
Make sure that the 2 upper claws are aligned and engage them.

Push down the steering pad and engage the lower claw.
- NOTICE:
- If the blind cover is stuck between the steering pad and the steering wheel, push it back to its original position.
| 11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 12. INSPECT SRS WARNING LIGHT |




