2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL WATER PUMP ASSEMBLY

  1. A099105
    Install a new gasket and the water pump with the 3 bolts and 2 nuts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }


2. INSTALL WATER PUMP PULLEY

  1. A099104E01
    Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 4 bolts to the specified torque.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }


3. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

  1. A125676E01
    Install the 7 bolts and nut, then install the engine mounting insulator RH.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for bolt A
    88 N*m{ 897 kgf*cm , 65 ft.*lbf } for bolt B
    52 N*m{ 530 kgf*cm , 38 ft.*lbf } for nut C
    20 N*m{ 199 kgf*cm , 14 ft.*lbf } for bolt D


4. INSTALL GENERATOR ASSEMBLY

A128376E01
  1. Provisionally install the generator with fixing bolt C.

  1. A128375E01
    Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolt A and nut B, then move the generator toward the cylinder block and tighten bolt B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for Bolt B

  1. A128374
    Install the connector.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.


5. INSTALL FAN AND GENERATOR V BELT
  1. Temporarily install the fan and generator V belt onto each pulley.

    NOTICE:
    1. Before installing the V belt, check each pulley for any kind of liquid and chips.
    1. Check that the ribs of the V belt are correctly fitted into the grooves of the pulleys.


6. ADJUST FAN AND GENERATOR V BELT

  1. A098655
    Insert a bar between the generator and the engine. Pull the bar toward the front of the vehicle and adjust the tension.

  1. A098654E01
    Tighten bolt A, then tighten bolt B.

    Torque:
    Bolt A:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }
    Bolt B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


7. INSPECT FAN AND GENERATOR V BELT

B000543
  1. Check the belt for wear, cracks and other signs of damage.
    If any defects are found, replace the V belt.

    HINT:
    Replace the drive belt if any of the following defects are found:
    1. The belt is worn out and the wire is exposed.
    2. The cracks reach the wire in more than one place.
    3. The belt has pieces missing from the ribs.

  1. B075171E01
    Check that the belt fits properly into the ribbed grooves.

    HINT:
    With your hand, confirm that the belt has not slipped out of the grooves on the bottom of the pulley.


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


9. ADD ENGINE COOLANT

A128306E01
  1. Remove air bleed valve A.

  1. A128305
    Fill the cooling system with coolant up to line B.

    Capacity:
    4.7 liters (5.0 US qts, 4.1 lmp. qts)

    HINT:
    1. Use of improper coolant may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. A128306E01
    Tighten air bleed valve A.

  1. Install the radiator cap.

  1. Warm up the engine.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Manual air conditioning system
      Automatic air conditioning system
      Set control as follows
      Fan speed - Any setting except "OFF"
      Temperature - Toward WARM
      Air conditioning switch "OFF"
      Fan speed - Any setting except "OFF"
      Temperature - To the highest temperature
      Air conditioning switch "OFF"
      "AUTO" switch "OFF"

  1. Run the engine at 3,000 rpm for 5 seconds and idling for 45 seconds alternately.

  1. Do the above operation for 7 minutes or more.

  1. After the engine cools down, check that the coolant level is between LOW and FULL lines.


10. CHECK ENGINE COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A128299
    Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

  1. Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.


11. INSTALL ENGINE UNDER COVER
  1. Provisionally install the engine under cover with the 5 bolts, 4 screws and 2 clips.

  1. Tighten the 4 screws.

  1. Tighten the 5 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


12. INSTALL ENGINE COVER SUB-ASSEMBLY NO. 1

A125743
  1. Engage the 4 pins and install engine cover No. 1.

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →