SERVICE DATA
Specifications · Vehicles built from Aug 2005
| Starter assembly |
Standard current |
50 A or less at 11.5 V |
| Starter relay |
Standard resistance 3 - 5 |
Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
| 10 kΩ or higher | ||
| Starter cut relay (w/ Entry and Start System) |
Standard resistance 3 - 5 |
Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
| 10 kΩ or higher | ||
| ACC relay (w/ Entry and Start System) |
Standard resistance 3 - 4 |
Below 1 Ω |
| 10 kΩ or higher (when battery voltage applied to terminals 1 and 2) | ||
| Standard resistance 3 - 5 |
Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
|
| 10 k Ω or higher | ||
| ACC cut relay (w/o Entry and Start System) |
Standard resistance 3 - 4 |
Below 1 Ω |
| 10 kΩ or higher (when battery voltage applied to terminals 1 and 2) | ||
| Standard resistance 3 - 5 |
Below 1 Ω(when battery voltage applied to terminals 1 and 2) |
|
| 10 kΩ or higher | ||
| AM2 fuse |
Standard resistance 1 - 2 |
Below 1 Ω |
| IG2 relay |
Standard resistance B1 - C1 |
Below 1 Ω |
| Standard resistance B1 - B4 |
10 kΩ or higher |
|
| Standard resistance B4 - C1 |
10 kΩ or higher |
|
| Standard resistance B2 - B3 |
Below 1 Ω |
|
| Standard resistance B1 - B4 |
Below 1 Ω (Apply battery voltage between terminals B2 and B3) |
|
| Standard resistance B4 - C1 |
Below 1 Ω (Apply battery voltage between terminals B2 and B3) |
|
| Engine switch (w/ Entry and Start System) |
Standard resistance 7 - 5 |
10 kΩ or higher (Released) |
| Below 1 Ω (Pushed) | ||
| Standard resistance 2 - 5 |
10 kΩ or higher (Released) |
|
| Below 1 Ω (Pushed) | ||
| Ignition relay |
Standard resistance 3 - 5 |
Below 1 Ω(when battery voltage applied to terminals 1 and 2) |
| 10 kΩ or higher | ||
| Ignition or starter switch assembly (w/o Entry and Start System) |
Standard resistance Between all terminals |
10 kΩ or higher (LOCK) |
| Standard resistance 2-4 |
Below 1 Ω (ACC) |
|
| Standard resistance 1-2-4 |
Below 1 Ω (ON) |
|
| Standard resistance 5-6 | ||
| Standard resistance 1-3-4 |
Below 1 Ω (START) |
|
| Standard resistance 5-6-7 | ||
| Starter armature assembly resistance |
Segments |
Below 1Ω |
| Commutator-Armature coil |
10kΩ or higher |
|
| Starter armature assembly commutator cirumference runout |
Maximum runout |
0.4mm (0.0157in.) |
| Starter armature assembly commutator diameter |
Standard diameter |
28.0mm (1.1024 in.) |
| Minimum diameter |
27.0mm (1.0630 in.) |
|
| Starter armature assembly undercut portion |
Standard undercut depth |
0.6mm (0.0236 in.) |
| Minimum undercut depth |
0.2mm (0.0079 in.) |
|
| Starter yoke assembly resistance |
Terminal C-Field coil brush lead (+) |
Below 1Ω |
| Brush lead (+)-starter yoke |
Below 1Ω |
|
| Brush length |
Standard length |
10mm (0.0.3937 in.) |
| Minimum length |
6mm (0.2362 in.) |
|
| Magnet starter switch assembly resistance |
Terminal C-Terminal l 50 |
Below 2Ω |
| Terminal 50-Magnet starter switch assembly |
Below 2Ω |
| Starter assembly |
Standard current |
65 A or less at 11.5 V |
| Starter relay |
Standard resistance 3 - 5 |
Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
| 10 kΩ or higher | ||
| Starter cut relay (w/ Entry and Start System) |
Standard resistance 3 - 5 |
Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
| 10 kΩ or higher | ||
| ACC relay (w/ Entry and Start System) |
Standard resistance 3 - 4 |
Below 1 Ω |
| 10 kΩ or higher (when battery voltage applied to terminals 1 and 2) | ||
| Standard resistance 3 - 5 |
Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
|
| 10 k Ω or higher | ||
| ACC cut relay (w/o Entry and Start System) |
Standard resistance 3 - 4 |
Below 1 Ω |
| 10 kΩ or higher (when battery voltage applied to terminals 1 and 2) | ||
| Standard resistance 3 - 5 |
Below 1 Ω(when battery voltage applied to terminals 1 and 2) |
|
| 10 kΩ or higher | ||
| AM2 fuse |
Standard resistance 1 - 2 |
Below 1 Ω |
| IG2 relay |
Standard resistance B1 - C1 |
Below 1 Ω |
| Standard resistance B1 - B4 |
10 kΩ or higher |
|
| Standard resistance B4 - C1 |
10 kΩ or higher |
|
| Standard resistance B1 - B4 |
Below 1 Ω (Apply battery voltage between terminals B2 and B3) |
|
| Standard resistance B4 - C1 |
Below 1 Ω (Apply battery voltage between terminals B2 and B3) |
|
| Engine switch (w/ Entry and Start System) |
Standard resistance 7 - 5 |
10 kΩ or higher (Released) |
| Below 1 Ω (Pushed) | ||
| Standard resistance 2 - 5 |
10 kΩ or higher (Released) |
|
| Below 1 Ω (Pushed) | ||
| Ignition relay |
Standard resistance 3 - 5 |
Below 1 Ω(when battery voltage applied to terminals 1 and 2) |
| 10 kΩ or higher | ||
| Ignition or starter switch assembly (w/o Entry and Start System) |
Standard resistance Between all terminals |
10 kΩ or higher (LOCK) |
| Standard resistance 2-4 |
Below 1 Ω (ACC) |
|
| Standard resistance 1-2-4 |
Below 1 Ω (ON) |
|
| Standard resistance 5-6 | ||
| Standard resistance 1-3-4 |
Below 1 Ω (START) |
|
| Standard resistance 5-6-7 | ||
| Starter armature assembly resistance |
Segments |
Below 1Ω |
| Commutator-Armature coil |
10kΩ or higher |
|
| Starter armature assembly commutator cirumference runout |
Standard runout |
0.02mm (0.0008in.) |
| Maximum runout |
0.04mm (0.0016in.) |
|
| Starter armature assembly commutator diameter |
Standard diameter |
35.0mm (1.378 in.) |
| Minimum diameter |
33.8mm (1.3307 in.) |
|
| Starter armature assembly undercut portion |
Standard undercut depth |
0.9mm (0.0354 in.) |
| Minimum undercut depth |
0.4mm (0.0157 in.) |
|
| Starter yoke assembly resistance |
Terminal C-Field coil brush lead (+) |
Below 1Ω |
| Brush lead (+)-starter yoke |
Below 1Ω |
|
| Starter brush holder assembly brush length |
Standard length |
12.5mm (0.4921 in.) |
| Minimum length |
7.0mm (0.2756 in.) |
|
| Starter brush holder assembly resistance |
A-B |
10kΩ or higher |
| A-C |
10kΩ or higher |
|
| A-D |
Below 1Ω |
|
| B-C |
Below 1Ω |
|
| B-D |
10kΩ or higher |
|
| C-D |
10kΩ or higher |
|
| Magnet starter switch assembly resistance |
Terminal C-Terminal l 50 |
Below 1Ω |
| Terminal 50-Magnet starter switch assembly |
Below 1Ω |
| Starter assembly |
Standard current |
90 A or less at 11.5 V |
| ACC cut relay |
Standard resistance 3 - 4 |
Below 1 Ω |
| 10 kΩ or higher (when battery voltage applied to terminals 1 and 2) | ||
| Standard resistance 3 - 5 |
Below 1 Ω(when battery voltage applied to terminals 1 and 2) |
|
| 10 kΩ or higher | ||
| AM2 fuse |
Standard resistance 1 - 2 |
Below 1 Ω |
| IG2 relay |
Standard resistance B1 - C1 |
Below 1 Ω |
| Standard resistance B1 - B4 |
10 kΩ or higher |
|
| Standard resistance B4 - C1 |
10 kΩ or higher |
|
| Standard resistance B2 - B3 |
Below 1 Ω |
|
| Standard resistance B1 - B4 |
Below 1 Ω (Apply battery voltage between terminals B2 and B3) |
|
| Standard resistance B4 - C1 |
Below 1 Ω (Apply battery voltage between terminals B2 and B3) |
|
| Ignition relay |
Standard resistance 3 - 5 |
Below 1 Ω(when battery voltage applied to terminals 1 and 2) |
| 10 kΩ or higher | ||
| Ignition or starter switch assembly. |
Standard resistance Between all terminals |
10 kΩ or higher (LOCK) |
| Standard resistance 2-4 |
Below 1 Ω (ACC) |
|
| Standard resistance 1-2-4 |
Below 1 Ω (ON) |
|
| Standard resistance 5-6 | ||
| Standard resistance 1-3-4 |
Below 1 Ω (START) |
|
| Standard resistance 5-6-7 | ||
| Starter armature assembly resistance |
Segments |
Below 1Ω |
| Commutator-Armature coil |
10kΩ or higher |
|
| Starter armature assembly commutator cirumference runout |
Maximum runout |
0.05mm (0.0020in.) |
| Starter armature assembly commutator diameter |
Standard diameter |
28.0mm (1.1024 in.) |
| Minimum diameter |
27.0mm (1.0630 in.) |
|
| Starter armature assembly undercut portion |
Standard undercut depth |
0.6mm (0.0236 in.) |
| Minimum undercut depth |
0.2mm (0.0079 in.) |
|
| Starter yoke assembly resistance |
Terminal C-Field coil brush lead |
Below 1Ω |
| Brush lead-starter yoke |
10kΩ or higher |
|
| Brush length |
Standard length |
14mm (0.5511 in.) |
| Minimum length |
9mm (0.3543 in.) |
|
| Starter brush holder assembly resistance |
Standard resistance |
10kΩ or higher |
| Magnet starter switch assembly resistance |
Terminal C-Terminal l 50 |
Below 1Ω |
| Terminal 50-Magnet starter switch assembly |
Below 2Ω |
| Starter assembly |
Standard current |
90 A or less at 11.5 V |
| ACC cut relay |
Standard resistance 3 - 4 |
Below 1 Ω |
| 10 kΩ or higher (when battery voltage applied to terminals 1 and 2) | ||
| Standard resistance 3 - 5 |
Below 1 Ω(when battery voltage applied to terminals 1 and 2) |
|
| 10 kΩ or higher | ||
| AM2 fuse |
Standard resistance 1 - 2 |
Below 1 Ω |
| IG2 relay |
Standard resistance B1 - C1 |
Below 1 Ω |
| Standard resistance B1 - B4 |
10 kΩ or higher |
|
| Standard resistance B4 - C1 |
10 kΩ or higher |
|
| Standard resistance B1 - B4 |
Below 1 Ω (Apply battery voltage between terminals B2 and B3) |
|
| Standard resistance B4 - C1 |
Below 1 Ω (Apply battery voltage between terminals B2 and B3) |
|
| Ignition relay |
Standard resistance 3 - 5 |
Below 1 Ω(when battery voltage applied to terminals 1 and 2) |
| 10 kΩ or higher | ||
| Ignition or starter switch assembly. |
Standard resistance Between all terminals |
10 kΩ or higher (LOCK) |
| Standard resistance 2-4 |
Below 1 Ω (ACC) |
|
| Standard resistance 1-2-4 |
Below 1 Ω (ON) |
|
| Standard resistance 5-6 | ||
| Standard resistance 1-3-4 |
Below 1 Ω (START) |
|
| Standard resistance 5-6-7 | ||
| Starter armature assembly resistance |
Segments |
Below 1Ω |
| Commutator-Armature coil |
10kΩ or higher |
|
| Starter armature assembly commutator cirumference runout |
Standard runout |
0.02mm (0.008in.) |
| Maximum runout |
0.05mm (0.0020in.) |
|
| Starter armature assembly commutator diameter |
Standard diameter |
29.0mm (1.142 in.) |
| Minimum diameter |
28.0mm (1.102 in.) |
|
| Starter brush holder assembly brush length |
Standard length |
15.5mm (0.610 in.) |
| Minimum length |
12mm (0.472 in.) |
|
| Starter brush holder assembly resistance |
A-B |
10kΩ or higher |
| A-C |
10kΩ or higher |
|
| A-D |
Below 1Ω |
|
| B-C |
Below 1Ω |
|
| B-D |
10kΩ or higher |
|
| C-D |
10kΩ or higher |
|
| Magnet starter switch assembly resistance |
Terminal C-Terminal l 50 |
Below 1Ω |
| Terminal 50-Magnet starter switch assembly |
Below 1.5Ω |