for DENSO Made
Battery
|
Standard specific gravity:
|
1.25 to 1.29 at 20°C (68°F)
|
Charging circuit without load
|
Standard amperage
|
10 A or less
|
Standard voltage
|
13.2 to 14.8 V
|
Charging circuit with load
|
Standard amperage
|
30 A or more
|
Generator brush holder assembly brush exposed length
|
Standard exposed length
|
9.5 to 11.5mm (0.374 to 0.453 in.)
|
Minimum exposed length
|
1.5mm (0.059 in.)
|
Generator regulator assembly resistance
|
F-B
|
When the positive and negative poles between terminals F and B are exchanged, there is continuity in one direction but no continuity in the other direction.
|
F-E
|
When the positive and negative poles between terminals F and E are exchanged, there is continuity in one direction but no continuity in the other direction.
|
Generator drive end frame resistance
|
Coil wires
|
Below 1Ω
|
Coil wire and body
|
10kΩ or higher
|
Generator holder with rectifier resistance
|
P1, P2, P3 -B
|
When the positive and negative poles among terminals P1, P2, P3 and B are exchanged, there is continuity in one direction but on continuity in the other direction.
|
P1, P2, P3 -E
|
When the positive and negative poles among terminals P1, P2, P3 and E are exchanged, there is continuity in one direction but on continuity in the other direction.
|
Generator rotor assembly resistance
|
Slip rings
|
1.7 to 2.1Ω at 20°C (68°F)
|
Slip ring and rotor
|
10kΩ or higher
|
Generator rotor assembly slip ring diameter
|
Standard diameter
|
14.2 to 14.4mm (0.559 to 0.564 in.)
|
Minimum diameter
|
12.8 mm (0.5.4 in.)
|
for BOSCH Made
Battery
|
Standard specific gravity:
|
1.25 to 1.29 at 20°C (68°F)
|
Charging circuit without load
|
Standard amperage
|
10 A or less
|
Standard voltage
|
13.2 to 14.8 V
|
Charging circuit with load
|
Standard amperage
|
30 A or more
|
Generator rotor assembly resistance
|
Slip rings
|
1.8 to 2.8 Ω at 20°C (68F°)
|
Slip rings and rotor
|
10 kΩ or higher
|
Generator rotor assembly slip ring diameter
|
Standard diameter
|
15.3 to 15.5 mm (0.602 to 0.610 in.)
|
Minimum diameter
|
14.9 mm (0.587 in.)
|
Starter sub-assembly generator with rectifier
|
Positive rectifier
|
Positive (+) tester probe - Positive (+) terminal
|
Below 1 Ω
|
Negative (-) tester probe - Rectifier terminal
|
Negative (-) tester probe - Positive (+) terminal
|
10 Ωor higher
|
Positive (+) tester probe - Rectifier terminal
|
Negative rectifier
|
Positive (+) tester probe - Negative (-) terminal
|
10 Ωor higher
|
Negative ( ) tester probe Rectifier terminal
|
Negative (-) tester probe - Negative (-) terminal
|
Below 1 Ω
|
Positive (+) tester probe - Rectifier terminal
|
Starter for open circuit
|
Between rectifier terminals
|
Below 1 Ω
|
Generator brush holder assembly
|
Exposed length
|
13.2 mm (0.520 in.)
|
Minimum exposed length
|
6.0 mm (0.236 in.)
|