2005-2008 Yaris · Service Manual COMMUNICATION SYSTEM

Brake Actuator (Skid Control ECU) Communication Stop Mode

Circuit diagnosis · Vehicles built from Aug 2005

DESCRIPTION

Detection Item
Symptom
Trouble Area
Brake Actuator (Skid Control ECU) Communication Stop Mode
  1. "ABS/VSC/TRC" not displayed on "Communication Bus Check" screen of intelligent tester
  2. Applies to "Brake Actuator (Skid Control ECU) Communication Stop Mode" in "DTC combination table"
  1. Power source circuit of brake actuator (skid control ECU)
  2. Brake actuator (skid control ECU) branch wire or connector
  3. Brake actuator (skid control ECU)

HINT:
For vehicle with ABS only.


WIRING DIAGRAM

C120497E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

    HINT:
    Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINE FOR DISCONNECTION (BRAKE ACTUATOR (SKID CONTROL ECU) BRANCH WIRE)

  1. TMC Made:

    1. C118165E03
      Turn the ignition switch off.

    2. Disconnect the A15 brake actuator (skid control ECU) connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A15-6 (CANH) - A15-5 (CANL)
      Ignition switch off
      54 to 69 Ω

  1. TMMF Made:

    1. C130880E03
      Turn the ignition switch off.

    2. Disconnect the A39 brake actuator (skid control ECU) connector.

    3. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A39-10 (CANH) - A39-8 (CANL)
      Ignition switch off
      54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BRAKE ACTUATOR (SKID CONTROL ECU) (CAN-H, CAN-L)
OK


2. CHECK HARNESS AND CONNECTOR (IG1, GND1)

  1. TMC Made:

    1. C118165E04
      Disconnect the A15 brake actuator (skid control ECU) connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A15-2 (GND1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      A15-25 (IG1) - Body ground
      Ignition switch on (IG)
      10 to 14 V

  1. TMMF Made:

    1. C130880E04
      Disconnect the A39 brake actuator (skid control ECU) connector.

    2. Measure the resistance.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A39-13 (GND1) - Body ground
      Always
      Below 1 Ω

    3. Measure the voltage.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      A39-7 (IG1) - Body ground
      Ignition switch on (IG)
      10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR (SKID CONTROL ECU)


← FAIL-SAFE CHART (from Aug 2005)ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode (from Aug 2005) →