2005-2008 Yaris · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Nov 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DRAIN ENGINE COOLANT

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. A117319
    Install a vinyl hose onto the radiator.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.

  1. Loosen the water drain plug, then drain the coolant.

    A128298E01


3. REMOVE FRONT WIPER ARM HEAD CAP

E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.


4. REMOVE FR WIPER ARM LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113850
    Remove the nut and front wiper arm.


5. REMOVE FR WIPER ARM RH

HINT:
Use the same procedure as for the LH side.


6. REMOVE HOOD TO COWL TOP SEAL

E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.

  1. E113852
    Disconnect the washer hose.

  1. Disengage the 11 claws and clip.

  1. E113854
    Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.


8. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.


10. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.


11. REMOVE FRONT WIPER MOTOR AND LINK

E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.


12. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

  1. A118801E01
    Disengage the claws and remove cowl to resister duct No. 2.


13. REMOVE COWL TOP PANEL OUTER

  1. A131386
    Disengage the clamp and separate the wiper motor connector.

  1. A131385
    Remove the 9 bolts and the cowl top panel outer.


14. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A127144
    Remove the grommet and 2 clamps and remove the air cleaner cap sub-assembly.


15. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

16. REMOVE PURGE VSV ASSEMBLY

  1. A127147
    Remove the bolt and remove the purge VSV assembly.


17. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A127148
    Disconnect the mass air flow meter connector.

  1. A127149
    Remove the 3 bolts and remove the air cleaner case sub-assembly.

  1. A127151
    Remove the O-ring from the throttle body assembly.


18. DISCONNECT NO. 1 WATER BY-PASS HOSE

  1. A127150
    Disconnect the 2 No. 1 water by-pass hoses.


19. DISCONNECT NO. 2 VENTILATION HOSE

  1. A127152
    Disconnect the No. 2 ventilation hose from the throttle body assembly.


20. DISCONNECT CHARCOAL CANISTER FUEL HOSE

  1. A127153
    Disconnect the charcoal canister fuel hose from throttle body assembly.


21. REMOVE THROTTLE BODY ASSEMBLY

  1. A127154
    Disconnect the connector from the throttle body assembly.

  1. A127155
    Remove the 3 bolts and remove the throttle body assembly.

  1. A127156
    Remove the O-ring from the intake manifold.


22. DISCONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

  1. A127161
    Disconnect the union to connector tube hose from the intake manifold.


23. DISCONNECT UNION TO CONNECTOR TUBE HOSE (for RHD)

  1. A127162
    Disconnect the union to connector tube hose from the intake manifold.


24. DISCONNECT VENTILATION HOSE (for LHD)

  1. A127163
    Disconnect the ventilation hose from the cylinder head.


25. DISCONNECT VENTILATION HOSE (for RHD)

  1. A127164
    Disconnect the ventilation hose from the cylinder head.


26. DISCONNECT ENGINE WIRE HARNESS (for LHD)

  1. A127165
    Disengage the 2 engine wire harness clamps.

  1. A131384
    Remove the bolt and remove the harness bracket.


27. DISCONNECT ENGINE WIRE HARNESS (for RHD)

  1. A127166
    A131384
    Disengage the 2 engine wire harness clamps.
    Remove the bolt and remove the harness bracket.


28. REMOVE THROTTLE BODY BRACKET

  1. A127168
    Remove the 2 bolts and remove the throttle body bracket.


29. REMOVE INTAKE MANIFOLD

  1. A127169
    Remove the 3 bolts and 2 nuts and remove the intake manifold.

  1. Remove the intake manifold gasket.


30. REMOVE KNOCK SENSOR

  1. A127170
    Disconnect the knock sensor connector.

  1. Remove the nut and remove the knock sensor.

← COMPONENTS (from Nov 2005)INSPECTION (from Nov 2005) →