INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL WATER PUMP ASSEMBLY |
Install the water pump assembly through a new gasket with the 3 bolts and 2 nuts.

- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
| 2. INSTALL WATER PUMP PULLEY |
Provisionally install the water pump pulley with the 4 bolts.
Using SST, hold the water pump pulley.

- SST
- 09960-10010
(09962-01000, 09963-00500)
Tighten the 4 bolts.
- Torque:
- 12 N*m{ 122 kgf*cm , 9 ft.*lbf }
| 3. INSTALL FAN AND GENERATOR V BELT |
Provisionally install the V belt onto the pulleys.
| 4. ADJUST FAN AND GENERATOR V BELT |
![]() ![]() |
Turn adjusting bolt C and adjust the tension of the V-belt.
Tighten fixing bolts A and B.
- Torque:
- 19 N*m{ 194 kgf*cm , 14 ft.*lbf } bolt A
- 44 N*m{ 449 kgf*cm , 33 ft.*lbf } bolt B
| 5. INSPECT FAN AND GENERATOR V BELT |
![]() ![]() |
Check the V belt deflection and tension.
- Deflection:
Item
Specified Condition
New belt
7.0 to 8.0 mm (0.28 to 0.31 in) w/ air conditioning system
4.0 to 5.0 mm (0.16 to 0.20 in) w/o air conditioning system
Used belt
9.0 to 9.5 mm (0.35 to 0.37 in) w/ air conditioning system
6.0 to 6.5 mm (0.24 to 0.26 in) w/o air conditioning system
- Tension:
Item
Specified Condition
New belt
687 to 883 N (70 to 90 kg, 154 to 199 ld) w/ air conditioning system
785 to 981 N (80 to 100 kg, 176 to 221 ld) w/o air conditioning system
Used belt
539 to 637 N (55 to 65 kg, 121 to 143 ld)
- HINT:
- Check the V belt deflection at the specified point.
- When installing a new belt, set its tension to the specified value.
- When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
- When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.
- V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.
- When using a belt tension gauge, confirm its accuracy by using a master gauge first.
- Check the V belt deflection at the specified point.
| 6. ADD ENGINE COOLANT |
Tighten all the plugs.
Disconnect the vinyl hose.
Pour engine coolant into the radiator assembly until it overflows.
- Capacity:
- 5.1 liters (5.4 USqts, 4.5 lmp. qts)
- NOTICE:
- Do not substitute plain water for engine coolant.
- HINT:
- Use of improper engine coolant may damage the engine coolant system.
- Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate engine coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- Use of improper engine coolant may damage the engine coolant system.
Check the engine coolant level inside the radiator assembly by squeezing the inlet and outlet radiator hoses several times by hand. If the engine coolant level goes down, add engine coolant.
Install the radiator cap sub-assembly securely.
Slowly pour engine coolant into the radiator reservoir until it reaches the FULL line.
Warm up the engine until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
Item
Manual air conditioning system
Automatic air conditioning system
Set control as follows
Fan speed - Any setting except "OFF"
Temperature - Toward WARM
Air conditioning switch "OFF"
Fan speed - Any setting except "OFF"
Temperature - To the highest temperature
Air conditioning switch "OFF"
"AUTO" switch "OFF"
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Stop the engine and wait until the coolant cools down.
If the engine coolant level is below the full level, perform steps (c) through (h) again and repeat the operation until the engine coolant level stays at the full level.
Recheck the engine coolant level inside the radiator reservoir tank assembly. If it is below the full level, add engine coolant.
| 7. CHECK FOR ENGINE COOLANT LEAKAGE |
- CAUTION:
- To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.
Fill the radiator assembly with engine coolant, then attach a radiator cap tester.

Pump it to 137 kPa (1.4 kgf/cm2, 19.9 psi), then check that the pressure does not drop.
If the pressure drops, check the hoses, radiator assembly and water pump assembly for leakage. If there are no signs or traces of external engine coolant leakage, check the heater core, cylinder block and head.
| 8. INSTALL ENGINE UNDER COVER RH |


