2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL FUEL INJECTOR ASSEMBLY

  1. A127656
    Install the 2 insulators onto fuel delivery pipe.

  1. A107004E01
    Apply a light coat of gasoline to 4 new O-rings and 4 new insulators, then install one onto each fuel injector.

  1. Apply a light coat of gasoline to the contact surfaces of the fuel delivery pipe and the O-rings and insulators of the fuel injector.

  1. A127205
    While turning the fuel injectors left and right, install them onto the fuel delivery pipe.

    NOTICE:
    1. Do not twist the O-ring.
    2. After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.


2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A127203
    Install the fuel delivery pipe sub-assembly with the 4 fuel injectors, then provisionally install the 2 bolts.

    NOTICE:
    1. Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
    2. Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe sub-assembly.

  1. Tighten the 2 bolts to the specified torque.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. A127655
    Insert the fuel tube connector into the fuel delivery pipe until a click sound can be heard.

    NOTICE:
    1. Check that there are no scratches or foreign matter around the disconnected parts of the fuel tube connector and pipe before performing this work.
    2. After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling them.

  1. A127194
    Install the fuel pipe clamp.

  1. A127200
    Connect the 4 fuel injector connectors.


3. CONNECT ENGINE WIRE HARNESS (for RHD)

  1. A127199
    Connect the 3 engine wire harness clamps and throttle body connector.


4. CONNECT ENGINE WIRE HARNESS (for LHD)

  1. A127198
    Connect the 4 engine wire harness clamps and throttle body connector.


5. CONNECT NO. 2 VENTILATION HOSE

  1. A127197
    Connect the No. 2 ventilation hose to the cylinder head.


6. CONNECT VENTILATION HOSE

  1. A127196
    Connect the ventilation hose to the cylinder head.


7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


8. CHECK FOR FUEL LEAKAGE

  1. A127178E01
    When using the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and the intelligent tester main switch ON.

      NOTICE:
      Do not start the engine.

    3. Select the Active Test mode on the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  1. Check that there is no fuel leakage anywhere in the fuel system after doing maintenance.


9. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A127151
    Install a new O-ring.

  1. A127149
    Install the air cleaner case sub-assembly with the 3 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. A127148
    Connect the connector to the mass air flow meter.


10. INSTALL PURGE VSV ASSEMBLY

  1. A127147
    Install the bolt and install the purge VSV assembly.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


11. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

12. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A127144
    Install the air cleaner cap with the grommet and 2 clamps.

← INSPECTION (from Nov 2005)COMPONENTS (from Nov 2005) →