2005-2008 Yaris · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Nov 2005


INSPECT STARTER ASSEMBLY

NOTICE:
Perform each of the following tests within 3 to 5 seconds.

  1. Perform pull-in test.

    1. Disconnect the field coil lead wire from terminal C.

    2. A128422E01
      Connect the battery to the starter magnetic switch as shown in the illustration and check that the pinion gear is extended.

  1. A128423E01
    Perform holding test.

    1. Check that the pinion gear does not return inward after the cable of terminal C is disconnected.

  1. A128424E01
    Inspect the clutch pinion gear return.

    1. Move the pinion gear toward the armature.

  1. Perform operation test without load.

    1. Connect the field coil lead wire to terminal C.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. Clamp the starter in a vise.

    3. A128425E01
      Connect the battery and ammeter to the starter as shown in the illustration.

    4. Check that the ammeter indicates the specified current.

      Standard current:
      90 A or less at 11.5 V


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A127351
    Check the plunger.

    1. Install the plunger and spring onto the switch body.

    2. A082640
      Push in the plunger, then check that it returns quickly to its original position.
      If necessary, replace the magnet starter switch assembly.

  1. A127352E01
    Check the pull-in coil for an open circuit.

    1. Using an ohmmeter, measure the resistance between terminals 50 and C.

      Standard resistance:
      Below 1 Ω

      If the standard is not met, replace the magnet starter switch assembly.

  1. A127353E01
    Check whether the hold-in coil has an open circuit.

    1. Using an ohmmeter, measure the resistance between terminals 50 and the switch body.

      Standard resistance:
      Below 1.5 Ω

      If the standard is not met, replace the magnet starter switch assembly.


INSPECT STARTER ARMATURE ASSEMBLY

  1. A082643E02
    Check the commutator for an open circuit.

    1. Using an ohmmeter, measure the resistance between the segments of the commutator.

      Standard resistance:
      Below 1 Ω

      If the standard is not met, replace the starter armature assembly.

  1. A082644E02
    Check the commutator for ground.

    1. Using an ohmmeter, measure the resistance between the commutator and the armature coil.

      Standard resistance:
      10 kΩ or higher

      If the standard is not met, replace the starter armature assembly.

  1. A082645
    Check the appearance.
    If the surface is dirty or burnt, restore the surface with 400-grit sandpaper on a lathe.

  1. Check the commutator circuit for runout.

    1. Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Standard runout:
      0.02 mm (0.0008 in.)

      Maximum runout:
      0.05 mm (0.0020 in.)

      If the runout is greater than the maximum, replace the armature assembly.

  1. A082646
    Using vernier calipers, measure the commutator diameter.

    Standard diameter:
    29 mm (1.142 in.)

    Minimum diameter:
    28 mm (1.102 in.)

    If the diameter is less than the minimum, replace the armature.


INSPECT STARTER BRUSH HOLDER ASSEMBLY
  1. Remove the claw of the spring, then remove the 4 brushes.

  1. Using vernier calipers, measure the brush length.

    Standard length:
    15.5 mm (0.610 in.)

    Minimum length:
    12 mm (0.472 in.)

    If the length is less than the minimum, replace the starter brush holder assembly.

    A095784E01

  1. A095705E01
    Check the brush holder.

    1. Using an ohmmeter, measure the resistance between the brushes.

      Standard resistance:
      Tester Connection
      Specified Condition
      A - B
      10 kΩ or higher
      A - C
      10 kΩ or higher
      A - D
      Below 1 Ω
      B - C
      Below 1 Ω
      B - D
      10 kΩ or higher
      C - D
      10 kΩ or higher

      If the standard is not met, replace the starter brush holder assembly.


INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY
  1. Inspect the gear teeth on the planetary gear, internal gear and starter clutch for wear and damage.
    If damaged, replace the gear or clutch assembly. Also check the planetary gear for wear or damage.

  1. A127354E01
    Inspect the starter clutch.

    1. Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
      If necessary, replace the starter center bearing clutch sub-assembly.

← DISASSEMBLY (from Nov 2005)REASSEMBLY (from Nov 2005) →