REASSEMBLY
Removal / installation · Vehicles built from Jan 2006
| 1. INSTALL REAR SIDE RAIL SPACER RH |
w/ Curtain Shield Airbag:

Align a new rear side rail spacer with the markings of the roof headlining and install it onto the roof headlining.
w/o Curtain Shield Airbag:

Align a new rear side rail spacer with the markings of the roof headlining and install it onto the roof headlining.
| 2. INSTALL REAR SIDE RAIL SPACER LH |
- HINT:
- Use the same procedure as for the RH side.
| 3. INSTALL FRONT SIDE RAIL SPACER RH |
w/ Curtain Shield Airbag:

Align a new front side rail spacer with the markings of the roof headlining and install it onto the roof headlining.
w/o Curtain Shield Airbag:

Align a new front side rail spacer with the markings of the roof headlining and install it onto the roof headlining.
| 4. INSTALL FRONT SIDE RAIL SPACER LH |
- HINT:
- Use the same procedure as for the RH side.
| 5. INSTALL ANTENNA CORD SUB-ASSEMBLY |
w/ Curtain Shield Airbag:
Install the part of the antenna cord marked with red positioning tape into claw A of the front side rail spacer.
Install the antenna cord positioning tapes into the 2 claws on the front and rear side rail spacers.
Insert the antenna cord positioning tape into the cutout of the roof headlining.
Align the antenna cord positioning tapes with the markings on the roof headlining.
Install the antenna cord onto the roof headlining with 6 new pieces of tape.


Tape size: Mark
Measurement
a
80 mm (3.15 in.)
b
20 mm (0.787 in.)
- NOTICE:
- Apply the tape securely in place.
- Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
- Apply the tape securely in place.
w/o Curtain Shield Airbag:
Install the part of the antenna cord marked with red positioning tape into claw A of the front side rail spacer.
Install the antenna cord positioning tapes into the 4 claws on the front and rear side rail spacers.
Insert the antenna cord positioning tape into the cutout of the roof headlining.
Align the antenna cord positioning tapes with the markings on the roof headlining.
Install the antenna cord onto the roof headlining with 4 new pieces of tape.


Tape size: Mark
Measurement
a
80 mm (3.15 in.)
b
20 mm (0.787 in.)
- NOTICE:
- Apply the tape securely in place.
- Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
- Apply the tape securely in place.
| 6. INSTALL ROOF WIRE |
w/ Curtain Shield Airbag:

Install part of the roof wire marked with red positioning tape into claw A of the front side rail spacer..
Align the roof wire positioning tape with the markings of the roof headlining.
Install the roof wire onto the roof headlining with 7 new pieces of tape.
Tape size: Mark
Measurement
a
80 mm (3.15 in.)
b
20 mm (0.787 in.)
- NOTICE:
- Apply the tape securely in place.
- Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
- Apply the tape securely in place.
w/o Curtain Shield Airbag:

Install part of the roof wire marked with red positioning tape into claw A of the front side rail spacer..
Install the roof wire positioning tape into the claw of the front side rail spacer.
Align the locating tape on the roof wire with the markings of the roof headlining.
Install the roof wire onto the roof headlining with 6 new pieces of tape.
Tape size: Mark
Measurement
a
80 mm (3.15 in.)
b
20 mm (0.787 in.)
- NOTICE:
- Apply the tape securely in place.
- Do not touch the adhesive surface when applying the tape to prevent adhesion failure.
- Apply the tape securely in place.
