2005-2008 Yaris · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jan 2006


1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR

B116929
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "Torx" socket wrench T25, install the power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. w/ Power window:

    1. Apply MP grease to the sliding and rotating areas of the rear door window regulator.

      NOTICE:
      Do not apply grease to the window regulator spring.

    2. B136217E01
      Loosely screw bolt A onto the rear door window regulator.

    3. Insert the rear door window regulator into the door panel. Use bolt A to hang the rear door window regulator on the door panel.

      NOTICE:
      Do not drop the window regulator as it may be damaged.

    4. Install the rear door window regulator with the 3 bolts, and tighten bolt A.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    5. Connect the connector.

  1. w/o Power window:

    1. Apply MP grease to the sliding and rotating areas of the rear door window regulator.

      NOTICE:
      Do not apply grease to the window regulator spring.

    2. B136232
      Install the rear door window regulator with the 3 bolts.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

B136216
  1. w/ Power window:

    1. Install the rear door glass onto the rear door window regulator.

  1. B136231
    w/o Power window:

    1. Install the rear door glass onto the rear door window regulator.


4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

B136214
  1. Install the rear door window division bar with the 2 bolts and screw.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }


5. INSTALL REAR DOOR GLASS RUN

B136213
  1. Install the rear door glass run.


6. INSTALL REAR DOOR BELT MOULDING

  1. B134882
    Engage the 5 claws and install a new rear door belt moulding.

  1. B134880E03
    Remove the protective tape.


7. INSTALL REAR DOOR WEATHERSTRIP

B136212
  1. Engage the 32 clips and install the rear door weatherstrip.


8. INSTALL REAR DOOR CHECK ASSEMBLY

B136211
  1. Apply MP grease to the sliding areas of the door check.

  1. Install the rear door check onto the door panel with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Install the rear door check onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


9. INSTALL REAR DOOR SERVICE HOLE COVER

  1. B136230E01
    Apply butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.

    Adhesive:
    Part No. 08850-00065, Butyl Tape Set or the equivalent

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.


10. INSTALL REAR DOOR TRIM BRACKET

  1. B136209
    Install the rear door trim bracket with the 2 screws.


11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

B136208
  1. Connect the rear door lock remote control cable and rear door inside locking cable.

  1. w/ Power window:
    Connect the connector.

  1. B136207
    Engage the 7 clips and install the rear door trim board.

  1. B136206
    Tighten the screw.


12. INSTALL REAR DOOR ARMREST BASE UPPER PANEL

B136205
  1. Engage the 4 claws and install the rear door armrest base upper panel.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

← INSPECTION (from Jan 2006)COMPONENTS (from Jan 2006) →