REPLACEMENT
Removal / installation · Vehicles built from Nov 2006
- CAUTION:
- Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. Used engine oil contains potentially harmful contaminants which may cause skin cancer.
- Take precautions when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves that cannot be penetrated by oil. Wash skin with soap and water, or use waterless hand cleaner, to remove any used engine oil completely. Do not use gasoline, thinner, or solvents.
- Dispose of used oil and used oil filters at designated disposal sites in order to preserve the environment.
- Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. Used engine oil contains potentially harmful contaminants which may cause skin cancer.
| 1. DRAIN ENGINE OIL |
Remove the oil pan drain plug and drain the engine oil.
Clean the oil pan drain plug and install it with a new gasket.
- Torque:
- 37 N*m{ 377 kgf*cm , 27 ft.*lbf }
| 2. REMOVE OIL FILTER ELEMENT |
Using SST, remove the oil filter cap.

- SST
- 09228-06501
- HINT:
- Use a container to catch the draining oil. Once the oil filter cap is loosened approximately 4 turns, the cap ribs become vertical and engine oil drains from the gap between the oil filter cap and oil pan.
Remove the oil filter element and O-ring from the oil filter cap.

- NOTICE:
- Be sure to remove the O-ring (from the cap) by hand, without using any tools, to prevent damage to the O-ring groove on the cap.
| 3. INSTALL OIL FILTER ELEMENT |
Clean the inside of the oil filter cap, threads and O-ring groove.

Apply a small amount of engine oil to a new O-ring and install it onto the oil filter cap.
Place a new oil filter element into the oil filter cap.
Remove any dirt or foreign matter from the installation surface of the engine.
Apply a small amount of engine oil to the O-ring again and install the oil filter cap.
Using SST, tighten the oil filter cap.

- SST
- 09228-06501
- Torque:
- 25 N*m{ 255 kgf*cm , 18 ft.*lbf }
- NOTICE:
- Make sure that the oil filter is installed securely as shown in the illustration.
- Make sure that the O-ring does not get caught between the parts.
- Make sure that the oil filter is installed securely as shown in the illustration.
| 4. ADD ENGINE OIL |
Fill with new engine oil.
- Engine oil:
Oil Grade
Oil Viscosity (SAE)
- API grade SL and energy-conserving
- API grade SM and energy-conserving
- ILSAC multigrade engine oil
- 0W-20
- 5W-20
- 5W-30
- 10W-30
- API grade SL
- API grade SM
- 15W-40
- 20W-50
- API grade SL and energy-conserving
- Oil capacity:
Item
Capacity
With oil filter change
4.2 liters (4.4 US qts, 3.7 Imp. qts)
Without oil filter change
3.9 liters (4.1 US qts, 3.4 Imp. qts)
Dry fill
4.7 liters (5.0 US qts, 4.1 Imp. qts)
| 5. INSPECT FOR ENGINE OIL LEAK |
| 6. INSPECT FOR OIL LEVEL |
Warm up the engine, then stop the engine and wait for 5 minutes. Check that the engine oil level is between the low and full marks on the oil level gauge.
If the engine oil level is low, check for oil leakage and add engine oil up to the full level mark.- NOTICE:
- Do not add engine oil to above the full level mark.
