2005-2008 Yaris · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Nov 2006


1. INSTALL AIR FUEL RATIO SENSOR

  1. A158282E01
    Using SST, install the air fuel ratio sensor.
    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }

  1. A158281
    Connect the air fuel ratio sensor connector and clamp.


2. INSTALL NO. 2 CYLINDER HEAD COVER

  1. A158207
    Disengage the 4 fittings shown and install the No. 2 cylinder head cover by applying pressure to it.

    HINT:
    Make sure that the oil and the engine oil level dipstick are correctly installed before installing the No. 2 cylinder head cover.


3. INSTALL COWL TOP PANEL OUTER

A115392
  1. Install the cowl top panel with the 9 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. A108438
    Connect the wire harness clamp.


4. INSTALL NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY

A108437
  1. Engage the claw to install No. 2 cowl to register duct.


5. INSTALL FRONT WIPER MOTOR AND LINK

E113861
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


6. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)

E113854
  1. Connect the washer hose.

  1. E113852
    Engage the 11 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.

  1. E117641
    Engage the 2 hooks and install cowl top ventilator louver center No. 1.


7. INSTALL COWL TOP VENTILATOR LOUVER LH (for LHD)

E113853
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the 2 clips.


8. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)

E113855
  1. Engage the 10 claws and install the cowl top ventilator louver sub-assembly.

  1. Install the clip.

  1. Connect the washer hose.


9. INSTALL COWL TOP VENTILATOR LOUVER LH (for RHD)

E113856
  1. Engage the 4 claws and install the cowl top ventilator louver LH.

  1. Install the clip.


10. INSTALL HOOD TO COWL TOP SEAL

E113851
  1. Engage the 7 clips and install the hood to cowl top seal.


11. INSTALL FRONT WIPER ARM LH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113862E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


12. INSTALL FRONT WIPER ARM RH

E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. E113863E01
    Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }


13. INSTALL FRONT WIPER ARM HEAD CAP

E113849
  1. Engage the claw and install the 2 front wiper arm head caps.


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


15. INSPECT FOR EXHAUST GAS LEAK
← INSPECTION (from Nov 2006)COMPONENTS (from Nov 2006) →