Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE AND WHEEL SYSTEM (for Sedan)

TIRE AND WHEEL SYSTEM (for Sedan) > INSPECTION

for Preparation Click here



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold tire inflation pressure:

    Vehicle Model
    Tire Size
    Vehicle Speed
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    NCP93R-BEMRKQ
    NCP93R-BEPRKQ
    175/65R14 82T
    185/60R15 84H
    Driving below 140 km/h (87 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 140 km/h (87 mph)
    260 (2.7, 38)
    260 (2.7, 38)
    NCP93L-BEMRK
    NCP93L-BEPRK
    NCP92L-BEMRK
    NCP92R-BEMRK
    NCP92L-BEPRK
    NCP92R-BEPRK
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)
    NCP93L-BEMRKV
    NCP93L-BEPRKV
    NCP92L-BEMRKV
    NCP92L-BEPRKV
    175/65R14 82T
    185/60R15 84H
    Driving below 160 km/h (100 mph)
    220 (2.2, 32)
    220 (2.2, 32)
    Driving over 160 km/h (100 mph)
    230 (2.3, 33)
    230 (2.3, 33)



    R003031E01
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    1.4 mm (0.055 in.) or less



2. ROTATE TIRES


C128523E01

HINT:
Rotate the tires, as shown in the illustration.



3. INSPECT WHEEL BALANCE


C080976E01
  1. Check and perform off-car balancing.

  1. If required, perform on-car balancing.

    Imbalance after adjustment:
    8 g (0.018 lb) or less



4. INSPECT FRONT AXLE HUB BEARING
  1. Remove the front wheel.

  1. Separate the disc brake caliper .

  1. Remove the front disc .



    C107912
  1. Inspect the axle hub backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the bearing.



    C107911
  1. Inspect the axle hub runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the runout exceeds the maximum, replace the bearing and axle hub.

  1. Install the front disc .

  1. Install the disc brake caliper .

  1. Install the front wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



5. INSPECT REAR AXLE HUB BEARING
  1. Remove the rear wheel.

  1. Remove the rear brake drum .



    C121815
  1. Inspect the axle hub and bearing backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the axle hub and bearing.



    C121816
  1. Inspect the axle hub and bearing runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.07 mm (0.0028 in.)

      If the runout exceeds the maximum, replace the axle hub and bearing.

  1. Install the rear brake drum.

  1. Adjust the rear drum brake shoe clearance .

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }