STEERING PAD (for Sedan) > DISPOSAL |
![]() |
| 1. DISPOSE OF STEERING PAD (WHEN INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
![]() |
Press the SST activation switch, and check that the LED of the SST activation switch illuminates.
Disconnect SST from the battery.
Disconnect the cable from the negative battery terminal.
![]() |
Remove the steering column cover.
Turn the steering wheel 90 degrees in both directions and remove the 2 screws.
Remove the screw from the lower portion of the steering cover lower.
Remove the steering column cover lower.
![]() |
Connect SST.
Disconnect the airbag connector, as shown in the illustration.
![]() |
Connect SST.
![]() |
Move SST to at least 10 m (33 ft) away from the vehicle front side window.
Maintaining enough clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (33 ft) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
| 2. DISPOSE OF STEERING PAD (WHEN NOT INSTALLED IN VEHICLE) |
![]() |
Check the function of SST.
![]() |
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
![]() |
Press the SST activation switch, and check that the LED of the SST activation switch illuminates.
Disconnect SST from the battery.
Disconnect the cable from the negative battery terminal.
Remove the steering pad (Click here).
![]() |
Using a service-purpose wire harness for the vehicle, tie the steering pad to the disc wheel.
| Area | Measurement |
| A | 1.25 mm2 or more (0.0019 in.2 or more) |
![]() |
Install the 2 bolts with washers into the 2 bolt holes in the steering pad.
| Area | Specification |
| L | 35.0 mm (1.378 in.) |
| M | 6.0 mm (0.236 in.) |
| Pitch | 1.0 mm (0.039 in.) |
![]() |
After connecting SST, connect it to the horn button.
![]() |
Using 3 wire harnesses, wind the wire harnesses at least 2 times each around the bolts installed on the left and right sides of the steering pad.
![]() |
Face the airbag deployment side of the steering pad upward. Using wire harnesses, separately tie the left and right sides of the steering pad to the disc wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole in the disc wheel.
![]() |
Connect SST.
Connect the SST connector.
Move SST to at least 10 m (33 ft) away from the steering pad tied to the disc wheel.
![]() |
Cover the steering pad with a cardboard box or tires.
Covering method using a cardboard box:
Cover the steering pad with the cardboard box and place weights of at least 190 N (19 kg, 43 lb) on the cardboard box in 4 places.
| Area | Measurement |
| X | 460 mm (18.11 in.) |
| Y | 650 mm (25.59 in.) |
![]() |
Covering method using tires:
Place at least 3 tires without disc wheels on top of the tire with a disc wheel to which the steering pad is tied.
| Area | Measurement |
| A | 185 mm (7.28 in.) |
| B | 360 mm (14.17 in.) |
![]() |
Tie the tires together with 2 wire harnesses.
![]() |
Deploy the airbag.
Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.
Check that no one is within a 10 m (33 ft) radius of the disc wheel to which the steering pad is tied.
Press the SST activation switch and deploy the airbag.
![]() |
Dispose of the steering pad.
Remove the steering pad from the disc wheel.
Place the steering pad in a plastic bag, tie it tightly and dispose of it according to local regulations.