LABEL (Intelligent Tester Display)
| Measure Item/Range
| Diagnostic Note
|
Injector
| Injection period of No.1 cylinder
| -
|
IGN Advance
| Ignition advance
| -
|
Calculate Load
| Calculated load
| Calculated load by ECM
|
Vehicle Load
| Vehicle load
| -
|
MAF
| Mass air flow volume
| If approximately 0.0 g/sec:
- Mass air flow meter power source circuit open or short
- VG circuit open or short
If 160.0 g/sec or more:
- E2G circuit open
|
Engine Speed
| Engine speed
| -
|
Vehicle Speed
| Vehicle speed
| Speed indicated on speedometer
|
Coolant Temp
| Engine coolant temperature
| If -40°C (-40°F), sensor circuit open If 140°C (284°F) or more, sensor circuit shorted
|
Intake Air
| Intake air temperature
| If -40°C (-40°F), sensor circuit open If 140°C (284°F) or more, sensor circuit shorted
|
Air-Fuel Ratio
| Ratio compared to stoichiometric level
| -
|
Purge Density Learn Value
| Learning value of purge density
| -
|
Purge Flow
| Ratio of evaporative purge flow to intake air volume
| -
|
EVAP (Purge) VSV
| EVAP purge VSV duty ratio
| -
|
Knock Correct Learn Value
| Correction learning value of knocking
| -
|
Knock Feedback Value
| Feedback value of knocking
| -
|
Accelerator Position No. 1
| Absolute Accelerator Pedal Position (APP) No. 1
| -
|
Accelerator Position No. 2
| Absolute APP No. 2
| -
|
Throttle Position
| Throttle sensor positioning
| -
|
Throttle Sensor Position
| Throttle position
| -
|
Throttle Sensor Position #2
| Throttle sensor positioning #2
| -
|
Throttle Motor
| Throttle motor
| -
|
O2S B1 S1
| Heated oxygen sensor output
| Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
O2S B1 S2
| Heated oxygen sensor output
| Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
Total FT #1
| Total fuel trim
| -
|
Short FT #1
| Short-term fuel trim
| Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
|
Long FT #1
| Long-term fuel trim
| Overall fuel compensation carried out in long-term to compensate a continual deviation of short-term fuel trim from central value
|
Fuel System Status (Bank 1)
| Fuel system status (Bank 1)
| - OL (Open Loop): Has not yet satisfied conditions to go closed loop
- CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
- OL DRIVE: Open loop due to driving conditions (fuel enrichment)
- OL FAULT: Open loop due to detected system fault
- CL FAULT: Closed loop but heated oxygen sensor, which used for fuel control malfunctioning
|
O2FT B1 S1
| Fuel trim at heated oxygen sensor
| -
|
O2 LR B1 S1
| Heated oxygen sensor response time (Lean to Rich)
| -
|
O2 RL B1 S1
| Heated oxygen sensor response time (Rich to Lean)
| -
|
Catalyst Temp (B1 S1)
| Estimated catalyst temperature (sensor 1)
| -
|
Catalyst Temp (B1 S2)
| Estimated catalyst temperature (sensor 2)
| -
|
Sub O2S Impedance B1S2
| Sub heated oxygen sensor impedance (sensor 2)
| -
|
Initial Engine Coolant Temp
| Engine coolant temperature at engine start
| -
|
Initial Intake Air Temp
| Intake air temperature at engine start
| -
|
Injection Volume (Cylinder 1)
| Injection volume
| -
|
ACC Relay
| ACC (Accessory) relay
| -
|
Starter Relay
| Starter relay (STA) signal
| -
|
Starter Signal
| Starter switch (STSW) signal
| -
|
Starter Control
| Starter control (STAR) signal
| -
|
Power Steering Switch
| Power Steering Signal
| -
|
Power Steering Signal
| Power Steering Signal (history)
| Signal status usually ON until battery terminals disconnected
|
Closed Throttle Position SW
| Closed throttle position switch
| -
|
A/C Signal
| A/C signal
| -
|
Neutral Position SW Signal
| Park/Neutral Position (PNP) switch signal
| -
|
Electrical Load Signal
| Electrical load signal
| -
|
Stop Light Switch
| Stop light switch
| -
|
Battery Voltage
| Battery voltage
| -
|
EVAP Purge VSV
| EVAP Purge VSV status
| -
|
Fuel Pump/Speed Status
| Fuel pump/speed status
| -
|
VVT Control Status (Bank 1)
| VVT control status
| -
|
Electric Fan Motor
| Electric fan motor
| -
|
TC and TE1
| TC and CG (TE1) terminals of DLC3
| -
|
VVT Aim Angle (Bank 1)
| VVT aim angle
| -
|
VVT Change Angle (Bank 1)
| VVT angle
| -
|
VVT OCV Duty (Bank 1)
| VVT OCV operation duty
| -
|
Idle Fuel Cut
| Fuel cut idle
| ON: when throttle valve fully closed and engine speed over 1,500 rpm
|
FC TAU
| Fuel cut during very light load
| Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete
|
Ignition
| Ignition counter
| -
|
Cylinder #1 Misfire Rate
| Cylinder #1 misfire rate
| Only displayed during idling
|
Cylinder #2 Misfire Rate
| Cylinder #2 misfire rate
| Only displayed during idling
|
Cylinder #3 Misfire Rate
| Cylinder #3 misfire rate
| Only displayed during idling
|
Cylinder #4 Misfire Rate
| Cylinder #4 misfire rate
| Only displayed during idling
|
All Cylinders Misfire Rate
| All cylinder misfire rate
| Only displayed during idling
|
Misfire RPM
| Engine speed when misfire occur
| -
|
Misfire Load
| Engine load when misfire occur
| -
|
Misfire Margin
| Margin to detect engine misfire
| -
|
Engine Run Time
| Accumulated engine running time
| -
|
Time after DTC Cleared
| Cumulative time after DTC cleared
| -
|
Distance from DTC Cleared
| Accumulated distance from DTC cleared
| -
|
Warmup Cycle Cleared DTC
| Warm-up cycle after DTC cleared
| -
|