HEADLIGHT ASSEMBLY (for Sedan) > REPAIR |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT BUMPER COVER |
![]() |
Apply protective tape, as shown in the illustration.
![]() |
Remove the 7 screws and 3 bolts.
Remove the 2 screw grommets.
Remove the 6 clips.
![]() |
w/ Fog Light:
Disengage the 6 claws and remove the front bumper cover.
Disconnect the 2 fog light connectors.
![]() |
w/o Fog Light:
Disengage the 6 claws and remove the front bumper cover.
![]() |
Remove the 2 clips and the screw grommet.
| 3. REMOVE HEADLIGHT ASSEMBLY |
![]() |
Remove the 2 screws and the bolt.
w/ Headlight leveling:
Disconnect the 3 connectors, then remove the headlight.
w/o Headlight leveling:
Disconnect the 2 connectors, then remove the headlight.
| 4. INSTALL HEADLIGHT PROTECTOR RETAINER UPPER |
![]() |
Cut off the portion indicated by the hatched lines in the illustration and smooth the surface with sandpaper.
![]() |
Install the headlight protector retainer upper with the 2 screws.
| 5. INSTALL HEADLIGHT PROTECTOR RETAINER LOWER |
![]() |
Cut off the portion indicated by the hatched lines in the illustration and smooth the surface with sandpaper.
![]() |
Install the headlight protector retainer lower with the 2 screws.
| 6. INSTALL HEADLIGHT ASSEMBLY |
![]() |
w/ Headlight leveling:
Connect the 3 connectors.
w/o Headlight leveling:
Connect the 2 connectors.
Install the headlight with the 2 screws and the bolt.
| 7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 8. INSTALL FRONT BUMPER COVER |
![]() |
Install the 2 clips and the screw grommet.
![]() |
w/ Fog Light:
Connect the 2 fog light connectors.
Engage the 6 claws and install the front bumper cover.
![]() |
w/o Fog Light:
Engage the 6 claws and install the front bumper cover.
![]() |
Install the 6 clips.
Install the 2 screw grommets.
Tighten the 7 screws and 3 bolts.
![]() |
Remove the protective tape.
| 9. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT |
Prepare the vehicle:
| 10. PREPARE FOR HEADLIGHT AIMING (for Using a Screen) |
![]() |
Prepare the following vehicle conditions:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft) high x 4 m (13.1 ft) wide) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen, as shown in the illustration.

![]() |
Draw base lines (H line, V LH and V RH lines) on the screen, as shown in the illustration.
H Line (Headlight height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.
V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) headlights):
Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).
| 11. INSPECT HEADLIGHT AIMING |
Cover the headlight on the opposite side or disconnect its connector, to prevent light from the headlight not being inspected from affecting the headlight aiming inspection.
Start the engine.
w/ Headlight leveling:
Set the headlight leveling switch to 0 (zero).
Turn on the headlight and make sure that the cutoff line falls within the specified area, as shown in the illustration.

| 12. ADJUST HEADLIGHT AIMING |
Adjust the aiming vertically:

Perform low-beam aim adjustment.
Adjust the aim horizontally:
Adjust the headlight aim to within the specified range by turning aiming screw B with a screwdriver.