Home › ENGINE ยท 2NZ-FE › FUEL › FUEL PUMP

FUEL PUMP > REMOVAL

for Preparation Click here


NOTICE:
Always use "TORX" socket wrench E10 when installing the rear seat.



1. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    B114569E01
  1. Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.



2. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106371
  1. Release the 2 knobs and remove the deck board.



3. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Remove the spare wheel cover.



4. REMOVE DECK FLOOR BOX (w/ Deck Board)


    B106373
  1. Release the 2 knobs and remove the deck floor box.



5. REMOVE REAR SEAT LEG COVER NO. 1 (for Hatchback)


    B126919E01
  1. Disengage the 4 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.



6. REMOVE REAR SEAT LEG COVER NO. 2 (for Hatchback)


    B126921E01
  1. Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.



7. REMOVE REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Hatchback Bench Seat Type)


    B117740
  1. Hold the front edge of the rear seat cushion and lift it up, as shown in the illustration, to disengage the the 2 rear seat cushion lock hooks.

    NOTICE:
    Hold the area around the rear seat cushion hooks so as to avoid deforming the rear seat cushion frame.

  1. Pass the rear seat inner belt through the slit in the rear seat cushion, disengage the hook between the rear seat cushion and rear seat back, and remove the rear seat cushion.



8. REMOVE REAR SEAT ASSEMBLY (for Hatchback)


    B114740
  1. Using "TORX" socket wrench E10, remove the 3 bolts and pull up the rear seat cushion.



    B117760
  1. Using "TORX" socket wrench E10, remove the 4 bolts and the rear seat.



9. REMOVE REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Sedan)


    B134922
  1. Hold the front edge of the rear seat cushion cover pad and lift it up, as shown in the illustration, to disengage the 2 hooks.

    NOTICE:
    Hold the area around the hooks so as to avoid deforming the rear seat cushion frame.

  1. Pass the rear seat inner belt through the slit in the rear seat cushion cover pad, disengage the hook between the rear seat cushion cover pad and the rear seatback, and remove the rear seat cushion cover pad.



10. REMOVE REAR FLOOR SERVICE HOLE COVER


A118713
  1. Remove the clip from the floor carpet.



    A118728
  1. Remove the rear floor service hole cover.



    A119173
  1. Disconnect the fuel pump connector.



11. DISCHARGE FUEL SYSTEM PRESSURE
  1. Discharge the fuel system pressure (Click here).



12. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


13. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


A119169
  1. Widen the tip of the tube joint clip and pull out the clip.

  1. Pull the fuel tank main tube to disconnect it.

    NOTICE:
    1. Keep the O-ring free of foreign matter, as it becomes contaminated easily.
    2. Do not use any tools in this procedure.
    3. Do not forcefully bend or twist the tube.
    4. Put the tube in a plastic bag to prevent damage and contamination.
    5. If the fuel suction plate and tube are stuck together, pinch the tube and turn it carefully to disconnect it.
    6. Do not damage any clips. If a clip is damaged, replace it.



14. DISCONNECT FUEL EMISSION TUBE NO. 2


A115476
  1. Loosen the clamp and disconnect fuel emission tube No. 2.



15. DISCONNECT CANISTER OUTLET HOSE SUB-ASSEMBLY NO. 1


A115477
  1. Disconnect the canister outlet hose.



16. REMOVE FUEL PUMP GAUGE RETAINER


A119171E01
  1. Using SST, remove the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    Align the claws of the fuel pump gauge retainer and the tips of SST.



17. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


A118739
  1. Remove the fuel suction with pump and gauge tube assembly.

    NOTICE:
    Do not bend the arm of the sender gauge.



    A118738
  1. Remove the fuel suction tube gasket from the fuel tank.