METER / GAUGE SYSTEM (for Hatchback) > ON-VEHICLE INSPECTION |
| 1. INSPECT SPEEDOMETER |
Check the operation.
Using a speedometer tester, inspect the speedometer and confirm that the speedometer readings are within the acceptable range. Also check the odometer operation.
| Standard Indication | Acceptable Range |
| 20 km/h | 21 to 25 km/h |
| 40 km/h | 41.7 to 46.2 km/h |
| 60 km/h | 62.7 to 67.2 km/h |
| 80 km/h | 83.4 to 88.4 km/h |
| 100 km/h | 104.3 to 109.3 km/h |
| 120 km/h | 125.1 to 130.6 km/h |
| 140 km/h | 145.8 to 151.8 km/h |
| 160 km/h | 166.2 to 173.2 km/h |
| Standard Indication | Acceptable Range |
| 20 mph | 21 to 23.5 mph |
| 40 mph | 42 to 44.5 mph |
| 60 mph | 62.5 to 66 mph |
| 80 mph | 83.1 to 87.1 mph |
| 100 mph | 103.9 to 108.4 mph |
| 120 mph | 124.7 to 129.6 mph |
| Standard Indication | Acceptable Range |
| 20 km/h | 20.6 to 24.6 km/h |
| 40 km/h | 41.1 to 45.1 km/h |
| 60 km/h | 61.7 to 65.9 km/h |
| 80 km/h | 82.2 to 86.2 km/h |
| 100 km/h | 102.8 to 108.8 km/h |
| 120 km/h | 123.3 to 129.3 km/h |
| 140 km/h | 143.9 to 149.9 km/h |
| 160 km/h | 164.4 to 170.4 km/h |
| 180 km/h | 185 to 191 km/h |
Check the deflection of the speedometer indicator.
| 2. INSPECT TACHOMETER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester on.
Select the item below from the Data List and read the value displayed on the intelligent tester.
| Item | Measurement Item/ Range(Display) | Normal Condition | Diagnostic Note |
| Engine Rpm | Engine speed / Min.: 0 rpm, Max.: 12,750 rpm | Approximately same as actual engine speed (When engine is running) | - |
Compare the engine speed displayed on the tester with the tachometer reading.
| Standard Indication | Acceptable Range [Data in ( ) are for reference] |
| 700 r/min | 630 to 770 r/min |
| 1,000 r/min | (900 to 1,100 r/min) |
| 2,000 r/min | (1,850 to 2,150 r/min) |
| 3,000 r/min | 2,800 to 3,200 r/min |
| 4,000 r/min | (3,800 to 4,200 r/min) |
| 5,000 r/min | 4,800 to 5,200 r/min |
| 6,000 r/min | (5,750 to 6,250 r/min) |
| 7,000 r/min | (6,700 to 7,300 r/min) |
| 3. INSPECT FUEL RECEIVER GAUGE |
![]() |
Disconnect the J5 fuel sender gauge connector.
Check the fuel receiver gauge operation when the ignition switch is turned ON.
Connect terminals 2 and 3 on the wire harness side connector of the fuel sender gauge.
Check the fuel receiver gauge operation when the ignition switch is turned from off to ON.
Reconnect the fuel sender gauge connector.
| 4. INSPECT FUEL LEVEL WARNING LIGHT |
![]() |
Disconnect the J5 fuel sender gauge connector.
Turn the ignition switch ON, and check that the receiver gauge No. 1 segment flashes when the fuel volume is less than 6.3 liters (less than 15 % of the total fuel tank capacity).
| Fuel Volume | Flashing Speed (Interval) |
| 6.3 liters (Less than 15 % of total fuel tank capacity) | Flashes slowly (1.2 seconds) |
| 4.2 liters (Less than 10 % of total fuel tank capacity) | Flashes quickly (0.6 seconds) |
| 5. INSPECT ENGINE OIL PRESSURE WARNING LIGHT |
Disconnect the engine oil pressure switch connector.
Turn the ignition switch ON.
Ground the terminal of the wire harness side connector, then check the engine oil pressure warning light.
Reconnect the engine oil pressure switch connector.
| 6. INSPECT BRAKE WARNING LIGHT |
Inspect the parking brake warning light.
Disconnect the parking brake switch connector.
Turn the ignition switch ON.
Ground the terminal of the wire harness side connector, then check the parking brake warning light.
Reconnect the parking brake switch connector.
Inspect the brake fluid level warning light.
Disconnect the brake fluid level warning switch connector.
Turn the ignition switch ON.
Connect a terminal to the other terminal of the wire harness side connector, then check the brake fluid level warning light.
Reconnect the brake fluid level warning switch connector.
| 7. INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
Remove the reservoir tank cap and strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance between the terminals.
Use a siphon or a similar tool to drain fluid out of the reservoir tank.
Measure the resistance between the terminals.
Pour the fluid back into the reservoir tank.
Reconnect the brake fluid level warning switch connector.
Reinstall the reservoir tank cap and strainer.
| 8. INSPECT ENGINE COOLANT TEMPERATURE WARNING LIGHT |
Disconnect the engine coolant temperature sensor connector.
Turn the ignition switch ON.
Connect a terminal to the other terminal of the wire harness side connector, then check the engine coolant temperature warning light.
Reconnect the engine coolant temperature sensor connector.
| 9. INSPECT ENGINE COOLANT TEMPERATURE INDICATOR LIGHT |
Disconnect the engine coolant temperature sensor connector.
Turn the ignition switch ON.
Reconnect the engine coolant temperature sensor connector.