Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS (for Hatchback)

WINDSHIELD GLASS (for Hatchback) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE FRONT WIPER ARM HEAD CAP


E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



3. REMOVE FRONT WIPER ARM BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113850
  1. Remove the nut and front wiper arm.



4. REMOVE FRONT WIPER ARM BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



5. REMOVE HOOD TO COWL TOP SEAL


E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.



    E113852
  1. Disconnect the washer hose.

  1. Disengage the 11 claws and clip.



    E113854
  1. Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.



7. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)


E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.



9. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)


E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



10. REMOVE FRONT DOOR SCUFF PLATE RH


    B114287
  1. Disengage the 6 claws and remove the rear door scuff plate.



11. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



12. REMOVE COWL SIDE TRIM BOARD RH


    B114285
  1. Disengage the claw and the stud bolt and remove the cowl side trim board.



13. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B130350
  1. Remove the front door opening trim weatherstrip.



15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



16. REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag)


B114299E01

HINT:
The number of the roof headlining service hole covers varies with the specifications.

  1. Using a clip remover with its tip wrapped in protective tape, remove the 6 roof headlining service hole covers.



17. REMOVE ASSIST GRIP COVER


B114301E01

HINT:
The number of the assist grip covers varies with the specifications.

  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 assist grip covers.



18. REMOVE ASSIST GRIP SUB-ASSEMBLY


B114302

HINT:
The number of the assist grips varies with the specifications.

  1. Disengage the 2 springs and remove the assist grip.



19. REMOVE VISOR ASSEMBLY RH


    B114303E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.



    B114304
  1. Remove the visor shaft from the visor holder.

  1. Disengage the 2 springs and remove the visor.



20. REMOVE VISOR ASSEMBLY LH

HINT:
Use the same procedure as for the RH side.



21. REMOVE VISOR HOLDER RH


    B114305E01
  1. Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.

    HINT:
    The claw may be damaged during removal. However, it is reusable because this does not effect its function.



22. REMOVE VISOR HOLDER LH

HINT:
Use the same procedure as for the RH side.



23. REMOVE MAP LIGHT ASSEMBLY


E114440
  1. Using a roof moulding remover, disengage the 4 claws.

  1. Disconnect the connector, and remove the map light.



24. REMOVE FRONT PILLAR GARNISH RH


    B117693E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117694
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114312
  1. Disconnect the connector.

  1. Using a clip remover, remove the 3 antenna cord clamps.



    B127674
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127670E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



  1. w/ Curtain Shield Airbag:



      B114313E01
    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



25. REMOVE FRONT PILLAR GARNISH LH


    B117695E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117696
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114316
  1. Using a clip remover, remove the 4 wire harness clamps.



    B127673
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127669E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



    B114317E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



26. REMOVE ROOF HEADLINING

HINT:
It is not necessary to remove the roof headlining completely. Slightly lower the front section of the roof headlining.



27. REMOVE INNER REAR VIEW MIRROR ASSEMBLY


B118043
  1. Pinch the cover, disengage the 2 claws and remove the cover.



    B087504
  1. Push the lever, and slide and remove the inner rear view mirror.



28. REMOVE WINDSHIELD OUTSIDE MOULDING


B107832E01
  1. Using a knife, cut off the windshield outside moulding, as shown in the illustration.

    NOTICE:
    Do not damage the vehicle body with the knife.

  1. Remove the windshield outside moulding.

    HINT:
    Make a partial cut in the windshield outside moulding. Then pull and remove it by hand.



29. REMOVE WINDSHIELD GLASS


B116958E01
  1. Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.

  1. From the interior, insert piano wires between the vehicle body and the windshield glass, as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

    NOTICE:
    1. When separating the windshield glass from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.
    2. To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.



    B081910E01
  1. Place matchmarks on the windshield glass and vehicle body in the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed unless the windshield glass is going to be reused.

  1. Cut through the adhesive by pulling the piano wire around the windshield glass.



    B116959E01
  1. Disengage the 2 stoppers.

  1. Using suction cups, remove the windshield glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the windshield glass.