WINDSHIELD GLASS (for Sedan) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT WIPER ARM HEAD CAP |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
| 3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
| 5. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.
| 6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 2 clips, the 6 claws and the 10 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD) |
![]() |
Disengage the 3 clips, the 4 claws and the 8 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 9. REMOVE FRONT DOOR SCUFF PLATE RH |
![]() |
Disengage the 11 claws and remove the front door scuff plate.
| 10. REMOVE FRONT DOOR SCUFF PLATE LH |
| 11. REMOVE COWL SIDE TRIM BOARD RH |
![]() |
Disengage the claw and the stud bolt and remove the cowl side trim board.
| 12. REMOVE COWL SIDE TRIM BOARD LH |
| 13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the front door opening trim weatherstrip.
| 14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 15. REMOVE FRONT PILLAR GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
Disconnect the antenna connector.
Using a clip remover, remove the 3 clamps.
![]() |
w/ Curtain Shield Airbag:
Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
| Area | Measurement |
| a | 700 mm (27.56 in.) |
| b | 120 mm (4.72 in.) |
| 16. REMOVE FRONT PILLAR GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
Using a clip remover, remove the 4 clamps.
![]() |
w/ Curtain Shield Airbag:
Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
| Area | Measurement |
| a | 700 mm (27.56 in.) |
| b | 120 mm (4.72 in.) |
| 17. REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Curtain Shield Airbag) |
![]() |
![]() |
Using a clip remover with its tip wrapped in protective tape, remove the 2 roof headlining service hole covers.
| 18. REMOVE ASSIST GRIP COVER |
![]() |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip cover.
| 19. REMOVE ASSIST GRIP SUB-ASSEMBLY |
![]() |
![]() |
Disengage the 2 springs and remove the assist grip.
| 20. REMOVE VISOR ASSEMBLY RH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the visor bracket cover.
![]() |
Remove the visor shaft from the visor holder.
Disengage the 2 springs and remove the visor.
| 21. REMOVE VISOR ASSEMBLY LH |
| 22. REMOVE VISOR HOLDER RH |
![]() |
Disengage the 2 claws by turning the visor counterclockwise between 60 to 120° and remove the visor holder.
| 23. REMOVE VISOR HOLDER LH |
| 24. REMOVE ROOM LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 covers.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.
![]() |
Disengage the roof wire from the claw of the room light.
Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.
Remove room light bulb No. 1.
| 25. REMOVE MAP LIGHT ASSEMBLY |
![]() |
Using a roof moulding remover, disengage the 4 claws.
Disconnect the connector, and remove the map light.
| 26. REMOVE INNER REAR VIEW MIRROR |
![]() |
Pinch the cover, disengage the 2 claws and remove the cover.
![]() |
Push the lever, and slide and remove the inner rear view mirror.
| 27. REMOVE ROOF HEADLINING ASSEMBLY |
| 28. REMOVE WINDSHIELD OUTSIDE MOULDING |
![]() |
Using a knife, cut off the windshield outside moulding, as shown in the illustration.
Remove the windshield outside moulding.
| 29. REMOVE WINDSHIELD GLASS |
![]() |
Apply protective tape to the outer circumference of the windshield glass, as shown in the illustration.
From the interior, insert piano wires between the vehicle body and the windshield glass, as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.
![]() |
Place matchmarks on the windshield glass and vehicle body in the locations indicated in the illustration.
Cut through the adhesive by pulling the piano wire around the windshield glass.
![]() |
Disengage the 2 stoppers.
Using suction cups, remove the windshield glass.