Home › BODY › WINDSHIELD / WINDOWGLASS › BACK WINDOW GLASS (for Sedan)

BACK WINDOW GLASS (for Sedan) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

NOTICE:
Always use "Torx" socket wrench E10 when removing the rear seat.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY
  1. for 60/40 Split Seat Type:

    1. Remove the rear seat cushion cover pad sub-assembly .

  1. for Fixed Seat Type:

    1. Remove the rear seat cushion cover pad sub-assembly .



3. REMOVE REAR SEATBACK ASSEMBLY LH (for 60/40 Split Seat Type)


    B134924
  1. Remove the rear seat outer belt from the rear seat shoulder belt guide.

  1. Pull the rear seatback lock release button and tilt the rear seatback forward.



    B134925
  1. Using a clip remover, remove the 2 clips and the rear seatback cover.



    B134926
  1. Remove the 2 bolts, the 2 hooks and the rear seatback.



4. REMOVE REAR SEATBACK ASSEMBLY RH (for 60/40 Split Seat Type)


    B134943
  1. Remove the rear seat outer belt from the rear seat shoulder belt guide.

  1. for 3 Point Type Rear Center Seat Belt:

    1. Remove the rear center seat outer belt from the rear center seat shoulder belt guide.

  1. Pull the rear seatback lock release button and tilt the rear seatback forward.



    B134944
  1. Using a clip remover, remove the 2 clips and the rear seatback cover.



    B134945
  1. Remove the 2 bolts, the 2 hooks and the rear seatback.



5. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)


    B138450E02
  1. Remove the rear seat outer belt from the rear seat shoulder belt guide.

    HINT:
    Use the same procedure for both sides.

  1. for 3 Point Type Rear Center Seat belt:

    1. Remove the rear center seat outer belt from the rear center seat shoulder belt guide.



    B134981
  1. Remove the 3 bolts.

  1. Disengage the 3 hooks and remove the rear seatback.



6. REMOVE LUGGAGE COMPARTMENT FLOOR MAT (for 60/40 Split Seat Type)


B136269
  1. Remove the luggage compartment floor mat.



7. REMOVE SPARE WHEEL COVER ASSEMBLY (for 60/40 Split Seat Type)


B136270
  1. Remove the spare wheel cover.



8. REMOVE LUGGAGE COMPARTMENT TRIM INNER PAD (for 60/40 Split Seat Type)


B136275
  1. Remove the luggage compartment trim inner pad.



9. REMOVE REAR DOOR SCUFF PLATE RH


    B134771
  1. Disengage the 7 claws and remove the rear door scuff plate.



10. REMOVE REAR DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



11. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B134772
  1. Remove the rear door opening trim weatherstrip.



12. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:
Use the same procedure as for the RH side.



13. REMOVE REAR SEAT SIDE COVER RH


    B134776
  1. Disengage the 2 clips and the 4 claws and remove the rear seat side cover.



14. REMOVE REAR SEAT SIDE COVER LH

HINT:
Use the same procedure as for the RH side.



15. REMOVE ROOF SIDE INNER GARNISH RH


    B134775E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    Replace the special clip with a new one when the roof side inner garnish is removed.


    1. Disengage the 4 clips and the claw and remove the roof side inner garnish.



    B134774
  1. w/o Curtain Shield Airbag:

    1. Disengage the 4 clips and the claw and remove the roof side inner garnish.



16. REMOVE ROOF SIDE INNER GARNISH LH

HINT:
Use the same procedure as for the RH side.



17. REMOVE ASSIST GRIP COVER


B134785

HINT:
The number of the assist grip covers varies with the specifications.



    B114301E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the assist grip cover.



18. REMOVE ASSIST GRIP SUB-ASSEMBLY


B134786

HINT:
The number of the assist grips varies with the specifications.



    B114302
  1. Disengage the 2 springs and remove the assist grip.



19. REMOVE HIGH MOUNTED STOP LIGHT ASSEMBLY (w/o Rear Spoiler)


    E127158
  1. Disengage the 2 claws.



    E127159
  1. Disengage the 2 claws.

  1. Disconnect the connector and remove the high mounted stop light assembly.



20. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    B134912
  1. for 3 Point Type Rear Center Seat Belt:

    1. Using a clip remover, remove the 4 clips.

    2. Disengage the 5 claws and remove the package tray trim panel.



    B134913
  1. for 2 Point Type Rear Center Seat Belt:

    1. Using a clip remover, remove the 3 clips.

    2. Disengage the 5 claws and remove the package tray trim panel.



21. REMOVE ROOF HEADLINING ASSEMBLY

HINT:
It is not necessary to remove the roof headlining completely. Slightly lower the rear section of the roof headlining.



22. REMOVE BACK WINDOW OUTSIDE MOULDING


B136256E01
  1. Using a knife, cut off the back window outside moulding, as shown in the illustration.

    NOTICE:
    Do not damage the vehicle body with the knife.

  1. Remove the back window outside moulding.

    HINT:
    Make a partial cut in the back window outside moulding. Then pull and remove it by hand.



23. REMOVE BACK WINDOW GLASS


B136257E01
  1. Apply protective tape to the outer circumference of the back window glass, as shown in the illustration.

  1. From the interior, insert piano wires between the vehicle body and the back window glass, as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

    NOTICE:
    1. When separating the back window glass from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.
    2. To prevent the safety pad from being scratched when removing the back window glass, place a plastic sheet between the piano wire and safety pad.



    B136258E02
  1. Place matchmarks on the back window glass and vehicle body in the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed unless the back window glass is going to be reused.

  1. Cut through the adhesive by pulling the piano wire around the back window glass.



    B136259E01
  1. Disengage the 2 stoppers.

  1. Using suction cups, remove the back window glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the back window glass.