Home › BODY › WINDSHIELD / WINDOWGLASS › QUARTER WINDOW GLASS (for 3 Door)

QUARTER WINDOW GLASS (for 3 Door) > INSTALLATION

for Preparation Click here



1. CLEAN QUARTER WINDOW GLASS


BO04421E01
  1. Clean the outer circumference of the glass with white gasoline.

    NOTICE:
    1. Do not touch the glass surface after cleaning it.
    2. Even if using a new glass, clean the glass with white gasoline.

    HINT:
    Since the pin is for positioning the glass, there is no need to replace it with a new one when reusing the glass, even if damaged.



2. CLEAN VEHICLE BODY


    B073084E02
  1. Clean and shape the contact surface of the vehicle body.

    1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

      NOTICE:
      Do not damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

      HINT:
      Clean the vehicle body even if all the adhesive has been removed.



3. INSTALL QUARTER WINDOW GLASS SPACER


B118063
  1. Coat the installation parts of the spacers with Primer G.

  1. Install 3 new spacers onto the glass, as shown in the illustration.



4. INSTALL QUARTER WINDOW MOULDING OUTSIDE FRONT


B121547E01
  1. Using a brush or sponge, apply Primer G to the edge of the quarter window and contact surface.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

  1. Install the quarter window moulding outside front, as shown in the illustration.

    Specification:
    Area
    Measurement
    a
    9.5 mm (0.374 in.)



5. INSTALL QUARTER WINDOW GLASS


H002865E01
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply Primer M to the adhesive.
    3. Throw away any leftover Primer M.
    4. Do not apply too much Primer M.



    B116963E01
  1. Using a brush or sponge, apply Primer G to the edge of the quarter window and contact surface.

    Specification:
    Area
    Measurement
    a
    6.0 mm (0.236 in.)
    b
    14 mm (0.551 in.)
    c
    7.5 mm (0.295 in.)
    d
    22 mm (0.866 in.)

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover Primer G.
    3. Do not apply too much Primer G.

    HINT:
    If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.



    B116964E01
  1. Apply adhesive.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. Cut the tip off the cartridge nozzle, as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time indicated in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the quarter window as shown in the illustration.

      Specification:
      Area
      Measurement
      a
      8 mm (0.315 in.)
      b
      12 mm (0.472 in.)
      c
      13 mm (0.512 in.)
      d
      14.5 mm (0.571 in.)
      e
      8 mm (0.315 in.)



  1. Install the quarter window glass onto the body.

    1. Hold the quarter window glass in place securely with protective tape or the equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check that the pins are attached to the body correctly.
      3. Check the clearance between the body and glass.

    2. Lightly press the front surface of the glass to ensure a close fit.



    3. B073131
    4. Using a scraper, remove any excessive or protruding adhesive.

      HINT:
      Apply adhesive to the quarter window glass rim.

      NOTICE:
      Do not to drive the vehicle within the time indicated in the table below.

      Minimum time:
      Temperature
      Minimum time prior to driving vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours



6. CHECK FOR LEAKAGE AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leakage with auto glass sealer.



7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY


    B114499
  1. Engage the 8 clips, the retainer and the 10 claws and install the front quarter trim panel.



    B114498
  1. Install the belt of the rear seat outer belt onto the rear seat shoulder belt hanger.



8. INSTALL FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY (for Sill Bar Type)


    B114759
  1. Install the front seat outer belt bar with the 2 bolts.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }



9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP


    B114546E01
  1. Align the location mark with the paint mark first, and install the front door opening trim weatherstrip, as shown in the illustration.
    Paint mark: 
    Area
    Color
    RH side
    Yellow
    LH side
    White



10. INSTALL FRONT DOOR SCUFF PLATE


    B114494
  1. Engage the 8 claws and install the front door scuff plate.



11. INSTALL REAR SEAT ASSEMBLY
  1. for RH Side:

    1. Install the rear seat assembly .

  1. for LH Side:

    1. Install the rear seat assembly .



12. INSTALL NO. 2 REAR SEAT LEG COVER (for LH Side)


    B114739
  1. Engage the 3 claws and install the No. 2 rear seat leg cover.



13. INSTALL NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Install the No. 1 rear seat leg cover .

  1. for LH Side:

    1. Install the No. 1 rear seat leg cover .



14. INSTALL DECK FLOOR BOX RH (w/ Deck Board)


    B106446
  1. Set the deck floor box and lock the 2 knobs.



15. INSTALL DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.



16. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Install the spare wheel cover.



17. INSTALL DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106447
  1. Set the deck board and lock the 2 knobs.



18. INSTALL REAR FLOOR CARPET ASSEMBLY


    B119912
  1. Install the rear floor carpet.



19. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)


    B114569E01
  1. Engage the 2 claws and install the package tray trim panel.

  1. Install the 5 pieces of hook tape.

  1. Install the 2 package tray trim suspenders.



20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }