Home › BODY › WINDSHIELD / WINDOWGLASS › QUARTER WINDOW GLASS (for 3 Door)

QUARTER WINDOW GLASS (for 3 Door) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)


    B114569E01
  1. Remove the 2 package tray trim suspenders.

  1. Remove the 5 pieces of hook tape.

  1. Disengage the 2 claws and remove the package tray trim.



3. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)


    B106371
  1. Release the 2 knobs and remove the deck board.



4. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Deck Board)


    B119913
  1. Remove the spare wheel cover.



5. REMOVE DECK FLOOR BOX RH (w/ Deck Board)


    B106372
  1. Release the 2 knobs and remove the deck floor box.



6. REMOVE DECK FLOOR BOX LH (w/ Deck Board)

HINT:
Use the same procedure as for the RH side.



7. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)


    B119912
  1. Remove the rear floor carpet.



8. REMOVE NO. 1 REAR SEAT LEG COVER
  1. for RH Side:

    1. Remove the No. 1 rear seat leg cover .

  1. for LH Side:

    1. Remove the No. 1 rear seat leg cover .



9. REMOVE NO. 2 REAR SEAT LEG COVER (for LH Side)


    B126921E01
  1. Disengage the 3 claws in the sequence shown in the illustration and remove the No. 1 rear seat leg cover.



10. REMOVE REAR SEAT ASSEMBLY
  1. for RH side:

    1. Remove the rear seat assembly .

  1. for LH Side:

    1. Remove the rear seat assembly .



11. REMOVE FRONT DOOR SCUFF PLATE


    B114494
  1. Disengage the 8 claws and remove the front door scuff plate.



12. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP


    B138507
  1. Remove the front door opening trim weatherstrip.



13. REMOVE FRONT SEAT OUTER BELT BAR SUB-ASSEMBLY (for Sill Bar Type)


    B114759
  1. Remove the 2 bolts and the front seat outer belt bar.



14. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY


    B114498
  1. Remove the belt of the rear seat outer belt from the rear seat shoulder belt hanger.



    B114499
  1. Disengage the 8 clips, the retainer and the 10 claws and remove the front quarter trim panel.



15. REMOVE QUARTER WINDOW MOULDING OUTSIDE FRONT


B116961E01
  1. Using a knife, cut off the quarter window moulding outside front.

    NOTICE:
    Do not damage the vehicle body with the knife.

    HINT:
    Make a partial cut in the quarter window moulding outside front. Then pull and remove it by hand.



16. REMOVE QUARTER WINDOW GLASS


B116962E01
  1. Apply protective tape to the outer circumference of the quarter window, as shown in the illustration.

  1. From the interior, insert piano wires between the vehicle body and quarter window, as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to all wire ends.

    NOTICE:
    When separating the quarter window from the vehicle, do not damage the vehicle's paintwork or exterior/interior ornaments.

  1. Cut through the adhesive by pulling the piano wire around the quarter window.