DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0136 | Following conditions (a) and (b) met for 4 minutes or more after engine warmed up (2 trip detection logic):
|
|
All of following conditions (a), (b), (c), (d) and (e) set (2 trip detection logic):
|


| Case | Heated Oxygen Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0136) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0136 | A |
| P0136 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 2)) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / O2S B1 S2.
Allow the engine to run at 2,500 rpm for 3 minutes.
Depress the accelerator pedal quickly until the engine rpm reaches 4,000 rpm 3 times.

|
| ||||
| NG | |
| 3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the D28 HO2 sensor (sensor 2) connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| HT1B (1) - +B (2) | 11 to 16 Ω at 20°C (68°F) |
| HT1B (1) - E2 (4) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 4.INSPECT INTEGRATION NO.1 RELAY (EFI RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI fuse.
Remove the EFI fuse from the integration relay.
Check the EFI fuse resistance.
Reinstall the EFI fuse.
Inspect the EFI relay.
Check the EFI relay resistance.
| Tester Connections | Specified Conditions |
| 1C-1 - 1A-4 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1A-2 and 1A-3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM) |
![]() ![]() |
Disconnect the D28 HO2 sensor (sensor 2) connector.
Disconnect the C20 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| OX1B (D28-3) - OX1B (C20-64) | Below 1 Ω |
| HT1B (D28-1) - HT1B (C20-47) |
| Tester Connections | Specified Conditions |
| OX1B (D28-3) or OX1B (C20-64) - Body ground | 10 kΩ or higher |
| HT1B (D28-1) or HT1B (C20-47) - Body ground |
Reconnect the ECM connector.
Reconnect the HO2 sensor connector.
|
| ||||
| OK | ||
| ||
| 6.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0136 | A |
| No output | B |
|
| ||||
| A | ||
| ||