STEERING COLUMN ASSEMBLY (for Hatchback) > REMOVAL |
| 1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE STEERING PAD (w/o Steering Pad Switch) |
![]() |
Using "TORX" socket wrench T30, loosen the 2 bolts completely.
Pull the steering pad toward you.
![]() |
Using a thin-bladed screwdriver, release the locking button.
Using a thin-bladed screwdriver, detach the airbag connector.
Detach the horn terminal.
| 4. REMOVE STEERING PAD (w/ Steering Pad Switch) |
![]() |
Using "TORX" socket wrench T30, loosen the 2 bolts completely.
Pull the steering pad toward you.
![]() |
Using a thin-bladed screwdriver, release the locking button.
Using a thin-bladed screwdriver, detach the airbag connector.
Detach the horn terminal.
| 5. REMOVE STEERING WHEEL ASSEMBLY |
![]() |
Remove the nut and place matchmarks on the steering wheel assembly and steering column assembly.
| *a | Matchmark |
![]() |
Using SST, remove the steering wheel assembly.
| 6. REMOVE STEERING COLUMN COVER |
![]() |
Remove the 3 screws, disengage the 2 claws, release the tilt lever and remove the steering column lower cover.
![]() |
Disengage the claw and remove the steering column upper cover.
| 7. REMOVE COMBINATION SWITCH ASSEMBLY |
Disconnect all connectors from the turn signal switch with spiral cable.
![]() |
Disengage the clamp indicated by the arrow in the illustration and remove the combination switch assembly from the steering column assembly.
| 8. REMOVE INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
with CD player
Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end LH.
![]() |
Except CD player
Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end LH.
| 9. REMOVE INSTRUMENT PANEL FINISH PANEL END RH |
![]() |
with CD player
Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end RH.
![]() |
Except CD player
Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end RH.
| 10. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL |
![]() |
![]() |
Disengage the 2 claws and 5 clips.
![]() |
After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.
Disengage the 3 A claws and remove the instrument cluster finish panel.
| 11. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Disconnect the 2 connectors.
Remove the 2 screws and pull the combination meter rearward to remove it.
| 12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
Separate the front door opening trim weatherstrip.
| 13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 14. REMOVE FRONT PILLAR GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
Disconnect the connector.
Using a clip remover, remove the 3 antenna cord clamps.
![]() |
w/ Front No. 2 Speaker:
Disconnect the speaker connector.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.
w/ Curtain Shield Airbag:
![]() |
Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
| Area | Measurement |
| a | 700 mm (27.56 in.) |
| b | 120 mm (4.72 in.) |
| 15. REMOVE FRONT PILLAR GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
Using a clip remover, remove the 4 wire harness clamps.
![]() |
w/ Front No. 2 Speaker:
Disconnect the speaker connector.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.
![]() |
w/ Curtain Shield Airbag:
Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
| Area | Measurement |
| a | 700 mm (27.56 in.) |
| b | 120 mm (4.72 in.) |
| 16. REMOVE SWITCH BASE HOLE COVER |
![]() |
Disengage the 2 clips and 2 claws and remove the switch hole base.
| 17. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.
![]() |
Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.
| 18. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY UPPER |
![]() |
Slide the slider and disconnect the passenger airbag connector.
Disconnect the clamp.
Remove the 2 <C> bolts and 4 <B> screws.

Disconnect the connectors.
Disengage the claw and 3 clips while lifting the rear instrument panel up.
While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.

| 19. DISCONNECT POWER STEERING ECU |
![]() |
Detach the power steering motor harness and torque sensor wire harness clamps from the power steering ECU side.
Disconnect the 2 steering column assembly connectors from the power steering ECU.
| 20. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Remove the 2 screws.
Disengage the 3 claws and remove the instrument panel under cover.
| 21. REMOVE INSTRUMENT PANEL UNDER TRAY (w/o Driver Side Knee Airbag) |
![]() |
Disengage the 4 claws and open the instrument panel under tray.
![]() |
Remove the 2 <A> screws.
Disengage the 4 claws and remove the instrument panel under tray.
| 22. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag) |
![]() |
Remove the 4 bolts.
Disengage the 6 claws and remove the driver side knee airbag assembly.
Using a thin-bladed screwdriver, release the locking button.
Using a thin-bladed screwdriver, disconnect the airbag connector and remove the instrument panel wire.
| 23. REMOVE COLUMN HOLE COVER SILENCER SHEET |
![]() |
Pull back the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.
| 24. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Loosen bolt A.
| *1 | Bolt A |
| *2 | Bolt B |
| *3 | Bolt C |
| *a | Matchmark |
Place matchmarks on the steering intermediate assembly and steering gear assembly.
Remove bolt B and detach the steering intermediate assembly from the steering gear assembly.
Place matchmarks on the steering intermediate assembly and steering column assembly.
Remove bolt C and detach the steering intermediate shaft assembly from the steering column assembly.
| 25. REMOVE BRAKE PEDAL (for Automatic Transaxle) |
![]() |
Using needle-nose pliers, remove the brake pedal return spring.
Remove the clip from the brake master cylinder push rod clevis pin.
Remove the brake master cylinder push rod clevis pin and detach the push rod clevis from the brake pedal.
Remove the bolt, nut and 2 brake pedal bushes, and remove the brake pedal assembly.
| 26. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle) |
![]() |
Remove the brake pedal return spring.
Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.
| 27. REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle) |
![]() |
Remove the 4 nuts and bolt and remove the pedal support.
| 28. REMOVE STEERING COLUMN ASSEMBLY |
Disconnect all connectors and detach all wire harness clamps from the steering column assembly.
![]() |
Remove the bolt and 2 nuts and remove the steering column assembly from the instrument panel reinforcement assembly.