FRONT PASSENGER AIRBAG ASSEMBLY (for Hatchback) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Remove the front door opening trim weatherstrip to the extent necessary to remove the front pillar garnish.
| 3. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 4. REMOVE FRONT PILLAR GARNISH RH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
Disconnect the connector.
Using a clip remover, remove the 3 antenna cord clamps.
![]() |
w/ Front No. 2 Speaker:
Disconnect the speaker connector.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.
w/ Curtain Shield Airbag:
![]() |
Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
| Area | Measurement |
| a | 700 mm (27.56 in.) |
| b | 120 mm (4.72 in.) |
| 5. REMOVE FRONT PILLAR GARNISH LH |
![]() |
w/ Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
w/o Curtain Shield Airbag:
Disengage the 2 clips and the 2 claws and remove the front pillar garnish.
![]() |
Using a clip remover, remove the 4 wire harness clamps.
![]() |
w/ Front No. 2 Speaker:
Disconnect the speaker connector.
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.
![]() |
w/ Curtain Shield Airbag:
Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
| Area | Measurement |
| a | 700 mm (27.56 in.) |
| b | 120 mm (4.72 in.) |
| 6. REMOVE INSTRUMENT PANEL FINISH PANEL END LH |
![]() |
with CD player
Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end LH.
![]() |
Except CD player
Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end LH.
| 7. REMOVE INSTRUMENT PANEL FINISH PANEL END RH |
![]() |
with CD player
Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end RH.
![]() |
Except CD player
Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.
Disconnect the connector and remove the instrument panel finish panel end RH.
| 8. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1 |
![]() |
![]() |
Disengage the 2 claws and 5 clips.
![]() |
After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.
Disengage the 3 A claws and remove the instrument cluster finish panel.
| 9. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Disconnect the 2 connectors.
Remove the 2 screws and pull the combination meter rearward to remove it.
| 10. REMOVE SWITCH HOLE BASE |
![]() |
Disengage the 2 clips and 2 claws and remove the switch hole base.
| 11. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY |
![]() |
Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.
![]() |
Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.
| 12. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Slide the slider and disconnect the passenger airbag connector.
Disconnect the clamp.
Remove the 2 <C> bolts and 4 <B> screws.

Disconnect the connectors.
Disengage the claw and 3 clips while lifting the rear instrument panel up.
While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.

| 13. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY |
![]() |
Remove the wire harness from the 2 claws of the instrument panel.
Disengage the 10 hooks and remove the instrument panel passenger airbag.
| 14. REMOVE INSTRUMENT PANEL WIRE ASSEMBLY |
![]() |
Using a thin-bladed screwdriver, release the locking button.
Using a thin-bladed screwdriver, disconnect the airbag connector and remove the instrument panel wire.