Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > TERMINALS OF ECM

for Preparation Click here



ECM

C105085E01

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Symbols (Terminal No.)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specific Condition".
Use the illustration above as a reference for the ECM terminals.


Symbols (Terminals No.)
Wiring Color
Terminal Description
Condition
Specified Condition
L (C20-74) - E1 (C20-104)
V - W
L shift position switch signal
Ignition switch ON and shift lever L position
10 to 14 V
Ignition switch ON and shift lever other than L position
Below 1 V
2 (C20-55) - E1 (C20-104)
G - W
2 shift position switch signal
Ignition switch ON and shift lever 2 position
10 to 14 V
Ignition switch ON and shift lever other than 2 position
Below 1 V
ODMS (A21-26) - E1 (C20-104)
BE - W
3 shift position switch signal
Ignition switch ON and shift lever 3 position
10 to 14 V
Ignition switch ON and shift lever other than 3 position
Below 1 V
D (C20-56) - E1 (C20-104)
L - W
D shift position switch signal
Ignition switch ON and shift lever D or 3 position
10 to 14 V
Ignition switch ON and shift lever other than D and 3 positions
Below 1 V
R (C20-53) - E1 (C20-104)
R - W
R shift position switch signal
Ignition switch ON and shift lever R position
10 to 14 V
Ignition switch ON and shift lever other than R position
Below 1 V
N (C20-54) - E1 (C20-104)
SB - W
N shift position switch signal
Ignition switch ON and shift lever N position
10 to 14 V
Ignition switch ON and shift lever other than N position
Below 1 V
P (C20-73) - E1 (C20-104)
R - W
P shift position switch signal
Ignition switch ON and shift lever P position
10 to 14 V
Ignition switch ON and shift lever other than P position
Below 1 V
NT+ (C20-125) - NT- (C20-124)
B - G
Speed sensor (NT) signal
Engine running
Pulse generation
(See waveform 1)
STP (A21-36) - E1 (C20-104)
G - W
Stop light switch signal
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
SPD (A21-8) - E1 (C20-104)
V - W
Speed signal
Ignition switch ON and driving wheel rotating slowly
Pulse generation
(See waveform 2)
S1 (C20-79) - E1 (C20-104)
SB - W
S1 solenoid signal
Ignition switch ON
10 to 14 V
1st or 2nd gear
10 to 14 V
3rd or 4th gear
Below 1 V
S2 (C20-78) - E1 (C20-104)
L - W
S2 solenoid signal
Ignition switch ON
Below 1 V
1st or 4th gear
10 to 14 V
2nd or 3rd gear
Below 1 V
ST (C20-80) - E1 (C20-104)
GR - W
ST solenoid signal
D position (3rd gear ←→ 4th gear)
Below 1 V ←→ 10 to 14 V
SLT+ (C20-76) - SLT- (C20-75)
G - W
SLT solenoid signal
Engine idling speed
Pulse generation
(See waveform 3)
SL (C20-57) - E1 (C20-104)
P - W
SL solenoid signal
Ignition switch ON
Below 1 V
Vehicle driving under lock up range
10 to 14 V
THO1 (C20-72) - ETHO (C20-95)
Y - B
ATF (Automatic Transmission Fluid) temperature sensor signal
ATF temperature: 10°C
(50°F) to 145°C (293°F)
4 to 0 V


    C053419E04
  1. Waveform 1
    Terminal
    NT+ - NT-
    Tool setting
    2 V/DIV, 1ms/DIV
    Vehicle conditions
    Driving at approximately 20 km/h (12 mph )



  2. C053421E04
  3. Waveform 2
    Terminal
    SPD - E1
    Tool setting
    2 V/DIV, 20 ms/DIV
    Vehicle conditions
    Driving at approximately 20 km/h (12 mph)



  4. C055887E01
  5. Waveform 3
    Terminal
    SLT+ - SLT-
    Tool setting
    5 V/DIV, 1 ms/DIV
    Vehicle conditions
    Engine idling speed