Home › TRANSMISSION ยท U441E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0711    Transmission Fluid Temperature Sensor "A" Performance

for Preparation Click here


DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input to the ECM.
The sensor resistance changes with the transmission fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies a voltage to the temperature sensor through ECM terminal THO1, and the ECM calculates the fluid temperature based on the voltage signal.

HINT:
The ATF temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No.
DTC Detection Condition
Trouble Area
P0711
Either of following Condition (A) or (B) is met:
Condition (A):
All of (a), (b) and (c) are detected. (2-trip detection logic)
(a) Intake air and engine coolant temperatures are more than -10°C (14°F) at engine start.
(b) After normal driving for over 9 minutes and 8 km (5.0 miles) or more, ATF temperature is less than 10°C (50°F).
(c) 19 minutes or more have elapsed after engine start.
Condition (B):
Both (a) and (b) are detected. (2-trip detection logic)
(a) Engine coolant temperature is less than 35°C (95°F) at engine start.
(b) ATF temperature is 100°C (212°F) or more when engine coolant temperature reaches 60°C (140°F).
  1. ATF level
  2. Transmission wire (ATF temperature sensor)
  3. ECM

MONITOR DESCRIPTION

The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects opens or shorts in the ATF temperature circuit or a fault of the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 10°C (50°F) after running the vehicle for a certain period, the ECM interprets this as a fault, and turns on the MIL.
When the ATF temperature is 100°C (212°F) or more and engine coolant temperature reaches 60°C (140°F) after cold start, the ECM also determines this as a fault, turns on the MIL, and stores the DTC.

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the Data List displayed by the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the Data List as the first step of troubleshooting is one method of shortening labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn on the tester.

  6. Select the following items: Powertrain / Engine and ECT / Data List.

  7. In accordance with the display on the tester, read the Data List.

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    A/T Oil Temperature 1
    ATF Temperature Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test; Approximately 80°C (176°F)
    2. Equal to ambient temperature when cold soak

    HINT:
    When DTC P0712 is output and intelligent tester reading is 150°C (302°F) or more, there is a short circuit.
    When DTC P0713 is output and intelligent tester reading is -40°C (-40°F), there is an open circuit.
    Measure the resistance between terminal THO1 and the body ground.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit

    HINT:
    If a circuit related to the ATF (Automatic Transmission Fluid) temperature sensor becomes open, P0713 is immediately set (within 0.5 seconds).
    It is not necessary to inspect the circuit when P0711 is set.

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0711)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn on the tester.

  1. Select the following items: Powertrain / Engine and ECT / DTC / Current or Pending.

  1. Read the DTCs using the tester.

    Result:

    Display (DTC output)
    Proceed to
    P0711
    A
    P0711 and other DTCs
    B

    HINT:
    If any other DTCs besides P0711 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.CHECK TRANSMISSION FLUID LEVEL

OK:
Automatic transmission fluid level is correct.



NG
ADD FLUID
OK

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)