Home › TRANSMISSION · U340E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0756    Shift Solenoid "B" Performance (Shift Solenoid Valve S2)

for Preparation Click here


DESCRIPTION

The ECM uses signals from the vehicle speed sensor and speed sensor NT to detect the actual gear position (1st, 2nd, 3rd or 4th).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect the mechanical problems of the shift solenoid valves, the valve body or automatic transaxle (clutch, brake or gear etc.).

DTC No.
DTC Detection Condition
Trouble Area
P0756
S2 stuck OFF malfunction*1:
Shifting to 1st and 4th gears is impossible.
ECM determines that there is malfunction when all of following conditions are met: (2-trip detection logic)
(a) When ECM directs gearshift to switch to 1st gear, actual gear is shifted to 2nd.
(b) When ECM directs gearshift to switch to 3rd gear, actual gear is shifted to 3rd.
(c) When ECM directs gearshift to switch to 4th gear, actual gear is shifted to 3rd.
  1. Shift solenoid valve S2 remains closed
  2. Valve body is blocked
  3. Shift solenoid valve S2
  4. Automatic transaxle (clutch, brake or gear etc.)
  5. ECM
P0756
S2 stuck ON malfunction*2:
Shifting to 2nd gear and 3rd gear is impossible.
ECM determines that there is malfunction when all of following conditions are met: (2-trip detection logic)
(a) When ECM directs gearshift to switch to 2nd gear, actual gear is shifted to 1st.
(b) When ECM directs gearshift to switch to 3rd gear, actual gear is shifted to 4th.
(c) When ECM directs gearshift to switch to 4th gear, actual gear is shifted to 4th.
  1. Shift solenoid valve S2 remains open
  2. Valve body is blocked
  3. Shift solenoid valve S2
  4. Automatic transaxle (clutch, brake or gear etc.)
  5. ECM

HINT:
Gear positions in the event of a solenoid valve mechanical problem:

Gearshift controlled by ECM
1st
2nd
3rd
4th
*1: Actual gear position under S2 stuck OFF malfunction
2nd
2nd
3rd
3rd
*2: Actual gear position under S2 stuck ON malfunction
1st
1st
4th
4th


MONITOR DESCRIPTION

This DTC indicates "stuck ON malfunction" or "stuck OFF malfunction" of shift solenoid valve S2.
The ECM controls the gearshifts by turning the shift solenoid valves ON/OFF. When the gear position directed by the ECM and the actual gear position do not match, the ECM illuminates the MIL and stores the DTC.

INSPECTION PROCEDURE


ACTIVE TEST

HINT:
Performing the Active Test using the intelligent tester allows components, such as the relay, VSV, and actuator, to be operated without removing any parts. Performing the Active Test as the first step of troubleshooting is one method of shortening labor time.
It is possible to display the Data List during the Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn on the tester.

  6. Select the following items: Powertrain / Engine and ECT / Active Test / Control the Shift Position.

  7. In accordance with the display on the tester, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed using the intelligent tester.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    Item
    Test Details
    Diagnostic Note
    Control the Shift Position
    [Test Details]
    Operate shift solenoid valve and set each shift position.
    [Vehicle Condition]
    1. IDL: ON
    2. 50 km/h (30 mph) or less
    [Others]
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves.

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
    2. The 3rd to 4th up-shifting must be performed with the accelerator pedal released.
    3. The 4th to 3rd down-shifting must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift more than once in succession.
    5. The shift position directed by the ECM is shown in the Data List / Shift Status display on the intelligent tester.
    6. Shift solenoid valve S2 is turned on/off normally when the shift lever is in the D position:

      Gearshift controlled by ECM
      1st
      2nd
      3rd
      4th
      Shift solenoid valve S2
      ON
      OFF
      OFF
      ON

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0756)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn on the tester.

  1. Select the following items: Powertrain / Engine and ECT / DTC / Current or Pending.

  1. Read the DTCs using the tester.


Result:

Display (DTC output)
Proceed to
P0756
A
P0756 and other DTCs
B

HINT:
If any other DTCs besides P0756 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT SHIFT SOLENOID VALVE S2
C130147E01
  1. Remove shift solenoid valve S2.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    Solenoid Connector (S2) - Solenoid Body (S2)
    11 to 15 Ω at 20°C (68°F)

  1. Connect the positive (+) lead to the terminal of the solenoid connector and the negative (-) lead to the solenoid body to check the solenoid valve operation.

OK:
The solenoid makes operating sounds.



NG
REPLACE SHIFT SOLENOID VALVE S2
OK


3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:
There are no foreign objects on any valves and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY
OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY