Home › TRANSMISSION · U340E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0705
When one of following conditions is met:
  1. Open or short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. Shift lock control unit assembly (Shift lock control ECU)
  4. ECM
Condition (A):
Any 2 or more of following signals are on simultaneously (2-trip detection logic).
P input signal is ON
N input signal is ON
R input signal is ON
D input signal is ON
2 input signal is ON
L input signal is ON
Condition (B):
Any 2 or more of following signals are on simultaneously (2-trip detection logic).
PNP switch (STAR) signal is ON
R input signal is ON
D input signal is ON
2 input signal is ON
L input signal is ON
Condition (C):
All of the following conditions are met (2-trip detection logic).
PNP switch (STAR) signal is OFF
P input signal is OFF
N input signal is OFF
R input signal is OFF
D input signal is OFF
2 input signal is OFF
L input signal is OFF
Condition (D):
When any of following conditions is met, the 3 or L position signal is ON for 2.0 seconds or more (2-trip detection logic).
PNP switch (STAR) signal is ON
P input signal is ON
N input signal is ON
R input signal is ON

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For safety, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in the P or N position.
The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, D, 2 or L). The ECM determines that there is a problem with the switch or related parts if it receives 2 or more position signals simultaneously or it receives no position signal. The ECM turns on the MIL and stores the DTC.

WIRING DIAGRAM


C189693E01


INSPECTION PROCEDURE


DATA LIST

HINT:
Using the Data List displayed by the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the Data List as the first step of troubleshooting is one method of shortening labor time.

  1. Turn the ignition switch off.

  2. Connect the intelligent tester to the DLC3.

  3. Turn the ignition switch to ON.

  4. Turn the tester on.

  5. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  6. In accordance with the display on the tester, read the Data List.


Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP (Park/Neutral Position) SW Status/
ON or OFF
Shift lever position;
P or N: ON
Except P and N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect.
Shift SW Status (R Range)
PNP SW Status/
ON or OFF
Shift lever position;
R: ON
Except R: OFF
Shift SW Status (P Range)
PNP SW Status/
ON or OFF
Shift lever position;
P: ON
Except P: OFF
Shift SW Status (N Range)
PNP SW Status/
ON or OFF
Shift lever position;
N: ON
Except N: OFF
Shift SW Status (D Range)
PNP SW Status/
ON or OFF
Shift lever position;
D or 3: ON
Except D and 3: OFF
Shift SW Status (3 Range)
PNP SW Status/
ON or OFF
Shift lever position;
3: ON
Except 3: OFF
Shift SW Status (2 Range)
PNP SW Status/
ON or OFF
Shift lever position;
2: ON
Except 2: OFF
Shift SW Status (L Range)
PNP SW Status/
ON or OFF
Shift lever position;
L: ON
Except L: OFF
1.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH)
C117645E80
  1. Disconnect the park/neutral position switch connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C27-2 (RB) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
C117645E81
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C27-4 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V



NG
Go to step 8
OK


3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
C130119E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (B) - 5 (L)
    Shift lever position P or N
    Below 1 Ω
    Shift lever position not P and N
    10 kΩ or higher
    2 (RB) - 6 (PL)
    Shift lever position P
    Below 1 Ω
    Shift lever position not P
    10 kΩ or higher
    1 (RL) - 2 (RB)
    Shift lever position R
    Below 1 Ω
    Shift lever position not R
    10 kΩ or higher
    2 (RB) - 9 (NL)
    Shift lever position N
    Below 1 Ω
    Shift lever position not N
    10 kΩ or higher
    2 (RB) - 7 (DL)
    Shift lever position D or 3
    Below 1 Ω
    Shift lever position not D and 3
    10 kΩ or higher
    2 (RB) - 3 (2L)
    Shift lever position 2
    Below 1 Ω
    Shift lever position not 2
    10 kΩ or higher
    2 (RB) - 8 (LL)
    Shift lever position L
    Below 1 Ω
    Shift lever position not L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
OK


4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (SHIFT LOCK CONTROL ECU)
C117648E26
  1. Disconnect the shift lock control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (AT3) - 9 (NSSD)
    Shift lever position 3
    Below 1 Ω
    Shift lever position not 3
    10 kΩ or higher



NG
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU)
C117647E12
  1. Connect the park/neutral position switch connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    9 (NSSD) - 8 (E)
    Ignition switch ON
    Shift lever position D or 3
    11 to 14 V
    Ignition switch ON
    Shift lever position not D and 3
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU - ECM)
A164217E14
  1. Connect the shift lock control ECU connector.

  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A21-26 (ODMS) - Body ground
    Ignition switch ON
    Shift lever position 3
    11 to 14 V
    Ignition switch ON
    Shift lever position not 3
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
C130155E10
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C20-73 (P) - Body ground
    Ignition switch ON
    Shift lever position P
    11 to 14 V
    Ignition switch ON
    Shift lever position not P
    Below 1 V
    C20-53 (R) - Body ground
    Ignition switch ON
    Shift lever position R
    11 to 14 V*
    Ignition switch ON
    Shift lever position not R
    Below 1 V
    C20-54 (N) - Body ground
    Ignition switch ON
    Shift lever position N
    11 to 14 V
    Ignition switch ON
    Shift lever position not N
    Below 1 V
    C20-56 (D) - Body ground
    Ignition switch ON
    Shift lever position D or 3
    11 to 14 V
    Ignition switch ON
    Shift lever position D and 3
    Below 1 V
    C20-55 (2) - Body ground
    Ignition switch ON
    Shift lever position 2
    11 to 14 V
    Ignition switch ON
    Shift lever position not 2
    Below 1 V
    C20-74 (L) - Body ground
    Ignition switch ON
    Shift lever position L
    11 to 14 V
    Ignition switch ON
    Shift lever position not L
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the back up light being turned on.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM 

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
C189694E01
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C20-52 (STAR) - C27-4 (B)
    Always
    Below 1 Ω
    C27-4 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM