DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0705 | When one of following conditions is met: |
|
| Condition (A): Any 2 or more of following signals are on simultaneously (2-trip detection logic). P input signal is ON N input signal is ON R input signal is ON D input signal is ON 2 input signal is ON L input signal is ON | ||
| Condition (B): Any 2 or more of following signals are on simultaneously (2-trip detection logic). PNP switch (STAR) signal is ON R input signal is ON D input signal is ON 2 input signal is ON L input signal is ON | ||
| Condition (C): All of the following conditions are met (2-trip detection logic). PNP switch (STAR) signal is OFF P input signal is OFF N input signal is OFF R input signal is OFF D input signal is OFF 2 input signal is OFF L input signal is OFF | ||
| Condition (D): When any of following conditions is met, the 3 or L position signal is ON for 2.0 seconds or more (2-trip detection logic). PNP switch (STAR) signal is ON P input signal is ON N input signal is ON R input signal is ON |

| DATA LIST |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
In accordance with the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP (Park/Neutral Position) SW Status/ ON or OFF | Shift lever position; P or N: ON Except P and N: OFF | When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP SW Status/ ON or OFF | Shift lever position; R: ON Except R: OFF | |
| Shift SW Status (P Range) | PNP SW Status/ ON or OFF | Shift lever position; P: ON Except P: OFF | |
| Shift SW Status (N Range) | PNP SW Status/ ON or OFF | Shift lever position; N: ON Except N: OFF | |
| Shift SW Status (D Range) | PNP SW Status/ ON or OFF | Shift lever position; D or 3: ON Except D and 3: OFF | |
| Shift SW Status (3 Range) | PNP SW Status/ ON or OFF | Shift lever position; 3: ON Except 3: OFF | |
| Shift SW Status (2 Range) | PNP SW Status/ ON or OFF | Shift lever position; 2: ON Except 2: OFF | |
| Shift SW Status (L Range) | PNP SW Status/ ON or OFF | Shift lever position; L: ON Except L: OFF |
| 1.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the park/neutral position switch connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C27-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C27-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
|
| ||||
| OK | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 (B) - 5 (L) | Shift lever position P or N | Below 1 Ω |
| Shift lever position not P and N | 10 kΩ or higher | |
| 2 (RB) - 6 (PL) | Shift lever position P | Below 1 Ω |
| Shift lever position not P | 10 kΩ or higher | |
| 1 (RL) - 2 (RB) | Shift lever position R | Below 1 Ω |
| Shift lever position not R | 10 kΩ or higher | |
| 2 (RB) - 9 (NL) | Shift lever position N | Below 1 Ω |
| Shift lever position not N | 10 kΩ or higher | |
| 2 (RB) - 7 (DL) | Shift lever position D or 3 | Below 1 Ω |
| Shift lever position not D and 3 | 10 kΩ or higher | |
| 2 (RB) - 3 (2L) | Shift lever position 2 | Below 1 Ω |
| Shift lever position not 2 | 10 kΩ or higher | |
| 2 (RB) - 8 (LL) | Shift lever position L | Below 1 Ω |
| Shift lever position not L | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (SHIFT LOCK CONTROL ECU) |
![]() |
Disconnect the shift lock control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (AT3) - 9 (NSSD) | Shift lever position 3 | Below 1 Ω |
| Shift lever position not 3 | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU) |
![]() |
Connect the park/neutral position switch connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 9 (NSSD) - 8 (E) | Ignition switch ON Shift lever position D or 3 | 11 to 14 V |
| Ignition switch ON Shift lever position not D and 3 | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU - ECM) |
![]() |
Connect the shift lock control ECU connector.
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A21-26 (ODMS) - Body ground | Ignition switch ON Shift lever position 3 | 11 to 14 V |
| Ignition switch ON Shift lever position not 3 | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C20-73 (P) - Body ground | Ignition switch ON Shift lever position P | 11 to 14 V |
| Ignition switch ON Shift lever position not P | Below 1 V | |
| C20-53 (R) - Body ground | Ignition switch ON Shift lever position R | 11 to 14 V* |
| Ignition switch ON Shift lever position not R | Below 1 V | |
| C20-54 (N) - Body ground | Ignition switch ON Shift lever position N | 11 to 14 V |
| Ignition switch ON Shift lever position not N | Below 1 V | |
| C20-56 (D) - Body ground | Ignition switch ON Shift lever position D or 3 | 11 to 14 V |
| Ignition switch ON Shift lever position D and 3 | Below 1 V | |
| C20-55 (2) - Body ground | Ignition switch ON Shift lever position 2 | 11 to 14 V |
| Ignition switch ON Shift lever position not 2 | Below 1 V | |
| C20-74 (L) - Body ground | Ignition switch ON Shift lever position L | 11 to 14 V |
| Ignition switch ON Shift lever position not L | Below 1 V |
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C20-52 (STAR) - C27-4 (B) | Always | Below 1 Ω |
| C27-4 (B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||