Home › RESTRAINTS › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



CHECK DLC3
H100769E16
  1. The ECU uses ISO 15765-4 for communication. The terminal arrangement of the DLC3 complies with ISO 15031-3 and matches the ISO 15765-4 format.

    Symbols (Terminal No.)
    Terminal Description
    Condition
    Specified Condition
    SIL (7) - SG (5)
    Bus " +" line
    During transmission
    Pulse generation
    CG (4) - Body ground
    Chassis ground
    Always
    Below 1 Ω
    SG (5) - Body ground
    Signal ground
    Always
    Below 1 Ω
    BAT (16) - Body ground
    Battery positive
    Always
    10 to 14 V
    CANH (6) - CANL (14)
    CAN bus line
    Ignition switch off*
    54 to 69 Ω
    CANH (6) - CG (4)
    HIGH-level CAN bus line
    Ignition switch off*
    200 Ω or higher
    CANL (14) - CG (4)
    LOW-level CAN bus line
    Ignition switch off*
    200 Ω or higher
    CANH (6) - BAT (16)
    HIGH-level CAN bus line
    Ignition switch off*
    6 kΩ or higher
    CANL (14) - BAT (16)
    LOW-level CAN bus line
    Ignition switch off*
    6 kΩ or higher

    NOTICE:
    *: Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.

    If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness and connector.


HINT:
B145842E01
Connect the cable of the intelligent tester to the DLC3, turn the ignition switch to ON and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
  1. If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
  2. If communication is still not possible when the tester is connected to another vehicle, the problem is probably in the tester itself. Consult the Service Department listed in the tester's instruction manual.


INSPECT BATTERY VOLTAGE

Standard voltage:
11 to 14 V

  1. If the voltage is below 11 V, recharge or replace the battery before proceeding.

INSPECT FRONT DRIVER SEAT BELT WARNING LIGHT
  1. Turn the ignition switch to ON.

  2. When the driver seat belt is not fastened, check that the combination meter's driver seat belt warning light blinks.

  3. When the seat belt is fastened, check that the combination meter's driver seat belt warning light turns off.


INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT
  1. Turn the ignition switch to ON.

  2. When the front passenger seat is occupied, seat belt is not fastened, check that the front passenger seat belt warning light on the instrument panel blinks.

  3. When the front passenger seat belt is fastened, check that the front passenger seat belt warning light turns off.


INSPECT SEAT BELT WARNING BUZZER USING DRIVER SEAT BELT
  1. Turn the ignition switch to ON.

  2. When the driver seat belt is not fastened within 0.4 seconds of the ignition switch being turned ON and the vehicle speed reaches 20 km/h (12.4 mph) or more, check that the buzzer sounds at 1.2 second intervals for 30 seconds.

  3. After the buzzer has sounded for 30 seconds, check that the buzzer sounds at 0.4 second intervals for a further 90 seconds.

  4. When 120 seconds have elapsed since the buzzer started sounding in step (c) above, check that the buzzer stops sounding.

  5. After the buzzer has stopped sounding, turn the ignition switch off and then start the engine again. With the driver seat belt unfastened, drive the vehicle at 20 km/h (12.4 mph) or more. Check that the buzzer sounds.

  6. After the buzzer has stopped sounding, fasten the driver seat belt, drive the vehicle at 20 km/h (12.4 mph) or more, and then unfasten the seat belt. Check that the buzzer sounds.

  7. After the buzzer has stopped sounding, move the shift lever to R. Then move the shift lever to D. With the driver seat belt unfastened, drive the vehicle at 20 km/h (12.4 mph) or more. Check that the buzzer sounds.