Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT (for Hatchback)

AIR CONDITIONING UNIT (for Hatchback) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here ).

HINT:
Use the same procedure for both the RH and LH sides.



1. BOLTS, SCREWS AND NUTS TABLE


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.



B118995E01



2. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.



    I101550E01
  1. Remove the caps from the service valves on the refrigerant line.

  1. Connect the Freon collection/recycling device to discharge the refrigerant gas remaining in the refrigeration system.

    NOTICE:
    Use the Freon collection/recycling device in accordance with the manufacturer's instruction manual.



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


4. DRAIN ENGINE COOLANT (for 1NZ-FE)

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.



  1. Loosen the cylinder block drain cock plug, then drain the coolant.


    A106596E01



5. DRAIN ENGINE COOLANT (for 2NZ-FE)

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.



  1. Loosen the cylinder block drain cock plug, then drain the coolant.


    A106596E01



6. REMOVE FRONT WIPER ARM HEAD CAP


E113848E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113850
  1. Remove the nut and front wiper arm.



8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



9. REMOVE HOOD TO COWL TOP SEAL


E113851
  1. Disengage the 7 clips and remove the hood to cowl top seal.



10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for LHD)


E117641
  1. Disengage the 2 hooks and remove cowl top ventilator louver center No. 1.



    E113852
  1. Disconnect the washer hose.

  1. Disengage the 11 claws and clip.



    E113854
  1. Disconnect the washer hose and remove the cowl top ventilator louver sub-assembly.



11. REMOVE COWL TOP VENTILATOR LOUVER LH (for LHD)


E113853
  1. Remove the 2 clips.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (for RHD)


E113855
  1. Disconnect the washer hose.

  1. Disengage the 10 claws and clip and remove the cowl top ventilator louver sub-assembly.



13. REMOVE COWL TOP VENTILATOR LOUVER LH (for RHD)


E113856
  1. Remove the clip.

  1. Disengage the 4 claws and remove the cowl top ventilator louver LH.



14. REMOVE FRONT WIPER MOTOR AND LINK


E113857
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



15. REMOVE NO. 2 COWL TO REGISTER DUCT SUB-ASSEMBLY


A108951
  1. Disengage the claw and remove cowl to register duct sub-assembly No. 2.



16. REMOVE COWL TOP PANEL OUTER


A108438
  1. Disengage the wire harness clamp.



    A115392
  1. Remove the 9 bolts and remove the cowl top panel outer.



17. DISCONNECT SUCTION TUBE SUB-ASSEMBLY


I101236
  1. Remove the bolt.

  1. Turn the hook type connector clockwise and disconnect the suction tube.

  1. Remove the O-ring from the suction tube.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.



18. DISCONNECT LIQUID TUBE SUB-ASSEMBLY
  1. Disconnect the liquid tube.

  1. Remove the O-ring from the liquid tube.

    NOTICE:
    Seal the opening of the disconnected parts with vinyl tape to prevent moisture and foreign matter from entering.



19. DISCONNECT HEATER WATER OUTLET HOSE A (FROM HEATER UNIT)


I101170
  1. Using pliers, grip the claw of the clip, slide the clip and disconnect the heater water outlet hose from the heater unit.



20. DISCONNECT HEATER WATER HOSE INLET A


I101171
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water inlet hose from the heater unit.



21. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


E107741E01
  1. with CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



    E107742E01
  1. Except CD player

    1. Pull the instrument panel finish panel end LH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end LH.



22. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


E107743E01
  1. with CD player

    1. Pull the instrument panel finish panel end RH and disengage the 4 claws and 3 clips.

      NOTICE:
      To avoid damaging the radio receiver and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



    E107744E01
  1. Except CD player

    1. Pull the instrument panel finish panel end RH rearward and disengage the 5 claws and 3 clips.

      NOTICE:
      To avoid damaging the instrument cluster finish panel center and the air conditioning panel, remove the instrument panel finish panel end without using any tool.

      HINT:
      Grip portion A of the instrument panel finish panel end and remove the instrument panel finish panel end from the lower side.

    2. Disconnect the connector and remove the instrument panel finish panel end RH.



23. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


B132363E01

NOTICE:
Follow the procedure below to remove the instrument cluster finish panel. Claw A will break if the instrument cluster finish panel is raised carelessly.



    B132364
  1. Disengage the 2 claws and 5 clips.



    B132365E01
  1. After removing the instrument panel finish panel end, insert your finger into the opening as shown, push the upper portion of the instrument cluster finish panel center and the 2 B claws of the instrument cluster finish panel, and then disengage the claws B.

  1. Disengage the 3 A claws and remove the instrument cluster finish panel.



24. REMOVE COMBINATION METER ASSEMBLY


E107730
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.



25. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER (Except CD Player)


B132368E02
  1. Disengage the 2 claws and 4 clips and remove the instrument cluster finish panel center.

    NOTICE:
    1. Grip the rib portion of the instrument cluster finish panel center by hand to remove it.
    2. To avoid breakage of the instrument cluster finish panel center when removing it, do not apply excessive force to the register or pull out the link or panel portions.



26. REMOVE RADIO TUNER OPENING COVER (w/o Radio Receiver)


B108169
  1. Remove the 4 bolts and the radio tuner opening cover.



27. REMOVE RADIO RECEIVER ASSEMBLY


E116761
  1. w/ Cassette Tape Player:

    1. Remove the 4 screws.

    2. Disconnect the connectors and remove the radio receiver.



    E116821E02
  1. w/ CD Player:

    1. Remove the 4 screws.

    2. Disengage the 2 claws and 4 clips and the radio receiver.

      NOTICE:
      1. Grip the rib portion of the radio receiver by hand to remove it.
      2. To avoid breakage of the radio receiver when removing it, do not apply excessive force to the register or pull out the link or panel portions.

    3. Disconnect the connectors.



28. REMOVE AIR CONDITIONER PANEL SUB-ASSEMBLY


I101155
  1. Disengage the 3 clips and 2 claws and remove the air conditioning panel.



    I101156
  1. Disconnect the 3 connectors and clamp.



29. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I101157
  1. Disconnect the air mix control cable from the clamp.

  1. Disengage the 2 claws and disconnect the air mix damper control cable.



30. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I101158
  1. Disengage the 2 claws and disconnect the defroster damper control cable.



31. DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I101159
  1. Disengage the 2 claws and disconnect the air inlet damper control cable.



32. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.



33. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.



34. REMOVE FRONT PILLAR GARNISH RH


    B117693E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117694
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114312
  1. Disconnect the connector.

  1. Using a clip remover, remove the 3 antenna cord clamps.



    B127674
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127670E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



  1. w/ Curtain Shield Airbag:



      B114313E01
    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



35. REMOVE FRONT PILLAR GARNISH LH


    B117695E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B117696
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B114316
  1. Using a clip remover, remove the 4 wire harness clamps.



    B127673
  1. w/ Front No. 2 Speaker:

    1. Disconnect the speaker connector.



    2. B127669E01
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the clip and hook and remove the front No. 2 speaker.



    B114317E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.
      Protective cover size: 
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



36. REMOVE NO. 1 SWITCH HOLE BASE (for LHD)


B108201
  1. Disengage the 2 clips and 2 claws and remove the switch hole base.



37. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B108202
  1. Slightly deform the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.



    B105351
  1. Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.



38. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B108181E02
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.



  1. Remove the 2 <C> bolts and 4 <B> screws.


    B105354E01

  1. Disconnect the connectors.

  1. Disengage the claw and 3 clips while lifting the rear instrument panel up.



  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.


    B105355E01



39. REMOVE FRONT DOOR SCUFF PLATE RH


    B114284
  1. Disengage the 8 claws and remove the front door scuff plate.



40. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



41. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH


    B114571
  1. Disengage the 4 claws and remove the instrument panel under cover.



42. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH


    B114572
  1. Remove the 2 screws.

  1. Disengage the 3 claws and remove the instrument panel under cover.



43. REMOVE COWL SIDE TRIM BOARD RH


    B114285
  1. Disengage the claw and the stud bolt and remove the cowl side trim board.



44. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



45. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


B208627
  1. Remove the shift lever knob.



46. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)


B208631
  1. Disengage the 6 claws and remove the shifting hole cover.



47. REMOVE CONSOLE BOX COVER REAR


B118991
  1. Disengage the 8 claws and remove the console box rear cover.



48. REMOVE CONSOLE BOX CARPET


B118992
  1. Remove the console box carpet.



49. REMOVE CONSOLE BOX ASSEMBLY REAR


B118993
  1. Remove bolt <F>.

  1. Disengage the 2 clips and remove the console box rear.



50. REMOVE INSTRUMENT PANEL UNDER TRAY


B108185
  1. Disengage the 4 claws and open the instrument panel under tray.



    B108187
  1. Remove the 2 <A> screws.

  1. Disengage the 4 claws and remove the instrument panel under tray.



51. REMOVE STEERING COLUMN COVER LOWER (w/ Driver Side Knee Airbag)


C118007
  1. Turn the steering wheel 90 degrees in both directions and remove the 2 screws.

  1. Remove the screw from the lower portion of the steering cover lower.

  1. Disengage the 2 claws and remove the steering column cover lower.



52. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


C119072E01
  1. Remove the 4 bolts.

  1. Disengage the 6 claws and remove the driver side knee airbag assembly.

  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the airbag connector and remove the instrument panel wire.



53. REMOVE INSTRUMENT PANEL BOX


B108188E01
  1. Open the instrument panel box.

  1. Pull the hinge side of the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.

  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.



54. REMOVE NO. 6 HEATER TO REGISTER DUCT ASSEMBLY


B108190
  1. Disengage the 4 claws and remove the heater to register duct.



55. DISCONNECT ANTENNA CORD SUB-ASSEMBLY


B108200
  1. for LHD:

    1. Disconnect the 2 antenna cord clamps.



    B108160E01
  1. for RHD:

    1. Disconnect the 3 antenna cord clamps.



56. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B108191
  1. Disengage the 3 claws and separate the hood lock control lever.



57. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


B108192
  1. Disengage the 2 claws and disconnect the DLC3 connector.

  1. Disconnect the clamps and connectors.



  1. Remove the 5 <D> bolts, 2 <E> bolts, screw <G> and screw <H> and remove the lower instrument panel.


    B108193E01



58. POSITION FRONT WHEELS FACING STRAIGHT AHEAD


59. REMOVE STEERING PAD
  1. w/o Steering Pad Switch:

    1. Remove the steering pad.

  1. w/ Steering Pad Switch:

    1. Remove the steering pad.



60. REMOVE STEERING WHEEL ASSEMBLY


    C117210E02
  1. Remove the nut and place matchmarks on the steering wheel assembly and steering column assembly.
    Text in Illustration 
    *a
    Matchmark



    C117207E01
  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of the SST center bolt before using.



61. REMOVE STEERING COLUMN COVER


    C117204E01
  1. Remove the 3 screws, disengage the 2 claws, release the tilt lever and remove the steering column lower cover.



    C117205E01
  1. Disengage the claw and remove the steering column upper cover.



62. REMOVE COMBINATION SWITCH ASSEMBLY
  1. Disconnect all connectors from the turn signal switch with spiral cable.



    C117206
  1. Disengage the clamp indicated by the arrow in the illustration and remove the combination switch assembly from the steering column assembly.



63. DISCONNECT POWER STEERING ECU


C117192
  1. Detach the power steering motor harness and torque sensor wire harness clamps from the power steering ECU side.

  1. Disconnect the 2 steering column assembly connectors from the power steering ECU.



64. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501E01
  1. Pull back the floor carpet, remove the 2 clips and remove the column hole cover silencer sheet.



65. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY


C118005E04
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft and the power steering link.

  1. Loosen bolt A, remove bolt B and remove the steering yoke.



66. REMOVE BRAKE PEDAL (for Automatic Transaxle)


C119065
  1. Using needle-nose pliers, remove the brake pedal return spring.

  1. Remove the clip from the brake master cylinder push rod clevis pin.

  1. Remove the brake master cylinder push rod clevis pin and detach the push rod clevis from the brake pedal.

  1. Remove the bolt, nut and 2 brake pedal bushes, and remove the brake pedal assembly.



67. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle)


C116880
  1. Remove the brake pedal return spring.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.



68. REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle)


C116881
  1. Remove the 4 nuts and bolt and remove the pedal support.



69. REMOVE STEERING COLUMN ASSEMBLY
  1. Disconnect all connectors and detach all wire harness clamps from the steering column assembly.



    C117203
  1. Remove the bolt and 2 nuts and remove the steering column assembly from the instrument panel reinforcement assembly.



70. REMOVE DEFROSTER NOZZLE ASSEMBLY
  1. Disconnect the connectors and clamps.



  1. Disengage the 5 claws and remove the defroster nozzle.


    I101175



71. REMOVE INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)


    I101593
  1. w/ Driver Side Knee Airbag:

    1. Disengage the clamp.

    2. Remove the 2 bolts, screw and nut and remove the instrument panel brace.



    I101595
  1. w/o Driver Side Knee Airbag:

    1. Disengage the clamp.

    2. Remove the bolt, screw and nut and remove the instrument panel brace.



72. REMOVE INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)


    I101594
  1. w/ Driver Side Knee Airbag:

    1. Disengage the 3 clamps.

    2. Remove the 2 bolts, screw and nut and remove the instrument panel brace.



    I101596
  1. w/o Driver Side Knee Airbag:

    1. Disengage the 3 clamps.

    2. Remove the bolt, screw and nut and remove the instrument panel brace.



73. SEPARATE MAIN BODY ECU (for LHD)


I101238
  1. Disconnect the 5 connectors and 3 the clamps.



    I101239
  1. Remove the 2 bolts and separate the main body ECU.



74. SEPARATE MAIN BODY ECU (for RHD)


I101536
  1. Disconnect the 5 connectors and the 5 clamps.



    I101537
  1. Remove the 2 bolts.

  1. Disengage the clamp and separate the main body ECU.



75. SEPARATE CONNECTOR NO. 2 HOLDER


I101240
  1. Remove the bolt.



    I100717
  1. Disconnect the connectors and separate the connector No. 2 holder.



76. REMOVE INSTRUMENT PANEL REINFORCEMENT


I101178
  1. Disconnect the drain hose.



    I101180
  1. Remove the bolt and disconnect the ground wire.



  1. Disconnect the connectors (for LHD).


    I101604



  1. Disconnect the connectors (for RHD).


    I101605



  1. Disengage the clamps (for LHD).


    I101182



  1. Disengage the clamps (for RHD).


    I101184



  1. Disconnect the connectors and clamps (for LHD).


    I104813



  1. Disconnect the connectors and clamps (for RHD).


    I104814



  1. Remove the 3 bolts and the nut.


    I101185



  1. Remove the 9 bolts and remove the instrument panel reinforcement together with the air conditioning unit.


    I101186



    I101242
  1. Disconnect the connector and 3 clamps.



    I101241
  1. Remove the 3 screws and the air conditioning unit.



77. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY


I101243
  1. Remove the screw and the air conditioning amplifier.



78. REMOVE AIR CONDITIONING UNIT


I101189
  1. Remove the 3 screws and the air conditioning unit.