Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › BLOWER UNIT (for Sedan)

BLOWER UNIT (for Sedan) > REMOVAL

for Preparation Click here


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here ).

HINT:
Use the same procedure for both the RH and LH sides.



1. BOLTS, SCREWS AND NUTS TABLE


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.



B132394E01



2. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start up the engine.

  1. Switch A/C ON.

  1. Turn the blower switch to ON.

  1. Operate the cooler compressor with an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the remaining compressor oil from each component, in the cooler compressor.

  1. Stop the engine.



    I101550E01
  1. Remove the caps from the service valves on the refrigerant line.

  1. Connect the Freon collection/recycling device to discharge the refrigerant gas remaining in the refrigeration system.

    NOTICE:
    Use the Freon collection/recycling device in accordance with the manufacturer's instruction manual.



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.


4. DRAIN ENGINE COOLANT (for 1NZ-FE)

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.



  1. Loosen the cylinder block drain cock plug, then drain the coolant.


    A106596E01



5. DRAIN ENGINE COOLANT (for 2NZ-FE)

NOTICE:
To avoid the danger of being burned, do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap sub-assembly.



  1. Loosen the cylinder block drain cock plug, then drain the coolant.


    A106596E01



6. DISCONNECT SUCTION TUBE SUB-ASSEMBLY


I101236
  1. Remove the bolt.

  1. Turn the hook type connector clockwise and disconnect the suction tube.

  1. Remove the O-ring from the suction tube.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.



7. DISCONNECT LIQUID TUBE SUB-ASSEMBLY
  1. Disconnect the liquid tube.

  1. Remove the O-ring from the liquid tube.

    NOTICE:
    Seal the openings of the disconnected parts with vinyl tape to prevent moisture and foreign matter from entering.



8. DISCONNECT HEATER WATER OUTLET HOSE


I101170
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water outlet hose from the heater unit.



9. DISCONNECT HEATER WATER INLET HOSE


I101171
  1. Using pliers, grip the claws of the clip, slide the clip and disconnect the heater water inlet hose from the heater unit.



10. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER


B132316
  1. Disengage the 2 claws and 2 clips and remove the instrument panel finish panel lower center.



11. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end LH.



12. REMOVE INSTRUMENT PANEL FINISH PANEL END RH


B132318
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end RH.



13. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


E116832
  1. Disengage the 4 claws and 5 clips and remove the instrument cluster finish panel.



14. REMOVE COMBINATION METER ASSEMBLY


E116819
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and pull the combination meter rearward to remove it.



15. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY


B132395
  1. Disengage the 2 claws and 4 clips and remove the instrument cluster panel center.



16. REMOVE STEREO OPENING COVER (w/o Radio Receiver)


B132396
  1. Remove the 4 screws and remove the stereo opening cover.



17. REMOVE RADIO RECEIVER ASSEMBLY


    B138302
  1. Remove the 4 bolts and the radio receiver.



    B138304
  1. Disconnect the plug.

  1. Disconnect the 2 radio connectors.



18. REMOVE AIR CONDITIONING PANEL ASSEMBLY


I102566
  1. Disengage the 4 clips and 2 claws and remove the air conditioning panel.



    I102567
  1. Disconnect the 3 connectors and 4 clamps.



19. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I102568
  1. Disconnect the air mix control cable from the clamp.

  1. Disengage the 2 claws and disconnect the air mix damper control cable.



20. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I102569
  1. Disengage the 2 claws and disconnect the defroster damper control cable.



21. DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I102570
  1. Disengage the 2 claws and disconnect the air inlet damper control cable.



22. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
  1. Separate the front door opening trim weatherstrip.



23. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Separate the front door opening trim weatherstrip.



24. REMOVE FRONT PILLAR GARNISH RH


    B134777E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134779
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134787
  1. Disconnect the antenna connector.

  1. Using a clip remover, remove the 3 clamps.



    B138437E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



25. REMOVE FRONT PILLAR GARNISH LH


    B134778E01
  1. w/ Curtain Shield Airbag:

    NOTICE:
    1. Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    2. Replace the special clip with a new one when the front pillar garnish is removed.


    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134780
  1. w/o Curtain Shield Airbag:

    1. Disengage the 2 clips and the 2 claws and remove the front pillar garnish.



    B134789
  1. Using a clip remover, remove the 4 clamps.



    B138438E01
  1. w/ Curtain Shield Airbag:

    1. Completely cover the curtain shield airbag with a piece of cloth or nylon and fix the ends of the fabric with adhesive tape, as shown in the illustration.

      Protective cover size:
      Area
      Measurement
      a
      700 mm (27.56 in.)
      b
      120 mm (4.72 in.)



26. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B132319E01
  1. Disengage the claw and separate the glove compartment door stopper from the glove compartment door.

  1. Slightly flex the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door until it becomes horizontal.



    B132320E01
  1. Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door.

    NOTICE:
    Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.



27. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY


B132322E01
  1. Slide the slider and disconnect the passenger airbag connector.

  1. Disconnect the clamp.



  1. Remove the 2 <C> bolts and 2 <B> screws.


    B132323E01



  1. Disengage the 7 clips by lifting the rear side of the instrument panel up.


    B132324

  1. While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws from the front side of the instrument panel and remove the instrument panel.



28. REMOVE FRONT DOOR SCUFF PLATE RH


    B134764
  1. Disengage the 11 claws and remove the front door scuff plate.



29. REMOVE FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



30. REMOVE COWL SIDE TRIM BOARD RH


    B114285
  1. Disengage the claw and the stud bolt and remove the cowl side trim board.



31. REMOVE COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



32. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B132387
  1. Remove the shift lever knob.



33. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B132347
  1. Shift the shift lever into the N position.

  1. Disengage the 5 clips and the claw and remove the upper console panel.



34. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY


    B132348
  1. Disengage the 3 clips and 3 claws.

  1. Disconnect the connector and remove the console upper rear panel.



35. REMOVE CONSOLE BOX CARPET


B132346
  1. Remove the console box carpet.



36. REMOVE REAR CONSOLE BOX ASSEMBLY


    B132349
  1. Disconnect the clamp.

  1. Remove the 2 bolts and 2 screws.

  1. Disengage the 4 claws and remove the rear console box.



37. REMOVE INSTRUMENT PAD LOWER LH


B132339
  1. Remove screw <I>.

  1. Disengage the claw and 3 clips and remove the instrument panel pad lower.



38. REMOVE INSTRUMENT PAD LOWER RH


B132340
  1. Remove screw <I>.

  1. Disengage the claw and 3 clips and remove the instrument panel pad lower.



39. REMOVE INSTRUMENT PANEL UNDER TRAY


B132341
  1. Disengage the 4 claws and open the instrument panel under tray.



    B132333
  1. Remove the 2 <A> screws.

  1. Disengage the 6 claws and remove the instrument panel under tray.



40. REMOVE INSTRUMENT PANEL BOX


B132334E01
  1. Open the instrument panel box.

  1. Pull the instrument panel box out horizontally with the instrument panel open and disengage the 2 hinges.



    B132335E01
  1. Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.



41. DISCONNECT ANTENNA CORD SUB-ASSEMBLY


    B132369
  1. for LHD:

    1. Disconnect the 5 antenna cord clamps.



    B132370
  1. for RHD:

    1. Disconnect the 4 antenna cord clamps.



42. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


B132338
  1. Disengage the 3 claws and separate the hood lock control lever.



43. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


B108192
  1. Disengage the 2 claws and disconnect the DLC3 connector.

  1. Disconnect the clamps and connectors.



  1. Remove the 6 <D> bolts, 2 <E> bolts, screw <G> and screw <H> and remove the lower instrument panel.


    B132342E01



44. POSITION FRONT WHEELS FACING STRAIGHT AHEAD


45. REMOVE STEERING PAD


C139082
  1. Using "TORX" socket wrench T30, loosen the 2 bolts completely.

  1. Pull the steering pad toward you.



    C139084E01
  1. Using a thin-bladed screwdriver, release the locking button.

  1. Using a thin-bladed screwdriver, disconnect the 2 connectors.

  1. Detach the horn terminal.



46. REMOVE STEERING WHEEL ASSEMBLY


    C139086E01
  1. Remove the nut and place matchmarks on the steering wheel assembly and steering column assembly.



    C139087
  1. Using SST, remove the steering wheel assembly.

    NOTICE:
    Apply a small amount of grease to the threads and tip of the SST center bolt before using.



47. REMOVE STEERING COLUMN COVER


    C139093E01
  1. Remove the 3 screws, disengage the 2 claws, release the tilt lever and remove the steering column lower cover.



    C139094E01
  1. Disengage the claw and remove the steering column upper cover.



48. REMOVE COMBINATION SWITCH ASSEMBLY
  1. Disconnect all connectors from the turn signal switch with spiral cable.



    C139088
  1. Disengage the clamp indicated by the arrow in the illustration and remove the combination switch assembly from the steering column assembly.



49. DISCONNECT POWER STEERING ECU


    C117192
  1. Detach the power steering motor harness and torque sensor wire harness clamps from the power steering ECU side.

  1. Disconnect the 2 steering column assembly connectors from the power steering ECU.



50. REMOVE COLUMN HOLE COVER SILENCER SHEET


    A116501E01
  1. Remove the floor carpet and 2 clips and remove the column hole cover silencer.



51. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY


C118005E04
  1. Place matchmarks on the sliding yoke of the steering intermediate shaft and the power steering link.

  1. Loosen bolt A, remove bolt B and remove the steering yoke.



52. REMOVE BRAKE PEDAL (for Automatic Transaxle)


    C119065
  1. Using needle-nose pliers, remove the brake pedal return spring.

  1. Remove the clip from the brake master cylinder push rod clevis pin.

  1. Remove the brake master cylinder push rod clevis pin and detach the push rod clevis from the brake pedal.

  1. Remove the bolt, nut and 2 brake pedal bushes, and remove the brake pedal assembly.



53. REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Manual Transaxle)


C116880
  1. Remove the brake pedal return spring.

  1. Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.



54. REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transaxle)


C116881
  1. Remove the 4 nuts and bolt and remove the pedal support.



55. REMOVE STEERING COLUMN ASSEMBLY


    C139089
  1. Disconnect all connectors and detach all wire harness clamps from the steering column assembly.

  1. Remove the bolt and 2 nuts and remove the steering column assembly from the instrument panel reinforcement assembly.



56. REMOVE HEATER TO REGISTER DUCT ASSEMBLY


I102581
  1. Disengage the 3 claws and remove the heater to register duct.



57. REMOVE DEFROSTER NOZZLE ASSEMBLY


I102582
  1. Disconnect the connector and 3 clamps.

  1. Disengage the 5 claws and remove the defroster nozzle.



58. REMOVE INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)


I101595
  1. Disengage the clamp.

  1. Remove the bolt, screw and nut and remove the instrument panel brace.



59. REMOVE INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)


I101596
  1. Disengage the 3 clamps.

  1. Remove the bolt, screw and nut and remove the instrument panel brace.



60. SEPARATE MAIN BODY ECU (DRIVER SIDE J/B) (for LHD)


I102583
  1. Disconnect the 5 connectors and the 3 clamps.



    I101239
  1. Remove the 2 bolts and separate the main body ECU.



61. SEPARATE MAIN BODY ECU (DRIVER SIDE J/B) (for RHD)


I102584
  1. Disconnect the 5 connectors and the 5 clamps.



    I101537
  1. Remove the 2 bolts.

  1. Disengage the clamp and separate the main body ECU.



62. SEPARATE CONNECTOR NO. 2 HOLDER


I102585
  1. Remove the bolt.



    I102615
  1. Disconnect the connectors and separate the connector No. 2 holder.



63. REMOVE INSTRUMENT PANEL REINFORCEMENT


I101178
  1. Disconnect the drain hose.



    I102586
  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect the connectors.



  1. Disengage the clamps (for LHD).


    I102588



  1. Disengage the clamps (for RHD).


    I102590



  1. Disconnect the connectors and clamps (for LHD).


    I102596



  1. Disconnect the connectors and clamps (for RHD).


    I102595



  1. Remove the 3 bolts and the nut.


    I102591



  1. Remove the 9 bolts and remove the instrument panel reinforcement together with the air conditioning unit.


    I102593



    I102594
  1. Remove the 3 screws and the air conditioning unit.



64. REMOVE BLOWER UNIT


I102599
  1. Remove the 3 screws and the blower unit.