Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Sedan)

DTC    C1425    Open in Stop Light Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU (housed in the actuator assembly) inputs the stop light switch signal and the condition of brake operation.
The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC NO.
DTC Detection Condition
Trouble Area
C1425
When IG1 terminal voltage is 9.5 V or more, an open circuit (A-B, A-ground) of the stop light switch continues for 3 seconds or more.
  1. Harness or connector
  2. Brake actuator assembly (skid control ECU)

WIRING DIAGRAM


C242033E07


INSPECTION PROCEDURE

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
INSPECT STOP LIGHT CIRCUIT (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).
    Result 
    Result
    Proceed to
    DTC (C1425) is not output
    A
    DTC (C1425) is output
    B

HINT:
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C231272E24
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the A76 brake actuator assembly (skid control ECU) connector.

  1. Check the connector case and terminals for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A76-28 (STP) - Body ground
    Stop light switch ON
    (Brake pedal depressed)
    8 to 14 V
    A76-28 (STP) - Body ground
    Stop light switch OFF
    (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly (Skid Control ECU))

  1. Reconnect the A76 brake actuator assembly (skid control ECU) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)