Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


JUNCTION CONNECTOR (LHD)


    E191937E03
  1. D-CAN Junction Connector
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to D-CAN Junction Connector)
    Wiring color 
    D-CAN Junction Connector
    Terminal No. (Symbol)
    Wiring Color
    Brake Actuator (Skid Control ECU)*1 (CAN-H)
    D41-1 (ABS)
    G
    Brake Actuator (Skid Control ECU)*1 (CAN-L)
    D41-12 (ABS)
    W
    DLC 3 (CAN-H)
    D41-3 (OBD)
    V
    DLC 3 (CAN-L)
    D41-14 (OBD)
    W
    ECM (CAN-H)
    D41-4 (EFI)
    L
    ECM (CAN-L)
    D41-15 (EFI)
    W
    Air Conditioning Amplifier*2 (TX+)
    D41-6 (A/C)
    V
    Air Conditioning Amplifier*2 (TX-)
    D41-17 (A/C)
    W
    Center Airbag Sensor Assembly (CAN-H)
    D41-8 (A/B)
    B
    Center Airbag Sensor Assembly (CAN-L)
    D41-19 (A/B)
    W
    CAN Main Wire (between D-CAN Junction Connector and P-CAN Junction Connector (CAN-H))
    D41-11 (TORH)
    Y
    CAN Main Wire (between D-CAN Junction Connector and P-CAN Junction Connector (CAN-L))
    D41-22 (TORH)
    W

    HINT:
    *1: w/ ABS
    *2: w/ Air Conditioning



  2. E191937E04
  3. P-CAN Junction Connector
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to P-CAN Junction Connector)
    Wiring color 
    P-CAN Junction Connector
    Terminal No. (Symbol)
    Wiring Color
    Power Steering ECU (CAN-H)
    D42-4 (EPS)
    SB
    Power Steering ECU (CAN-L)
    D42-15 (EPS)
    W
    Main Body ECU (CAN-H)
    D42-5 (JB)
    R
    Main Body ECU (CAN-L)
    D42-16 (JB)
    W
    Combination Meter ECU (CAN-H)
    D42-7 (MET)
    G
    Combination Meter ECU (CAN-L)
    D42-18 (MET)
    W
    CAN Main Wire (between P-CAN Junction Connector and D-CAN Junction Connector (CAN-H))
    D42-11 (TOLH)
    Y
    CAN Main Wire (between P-CAN Junction Connector and D-CAN Junction Connector (CAN-L))
    D42-22 (TOLH)
    W



  4. Wiring diagram for identifying CAN junction connectors


    E191973E01


JUNCTION CONNECTOR (RHD)


    E191937E04
  1. D-CAN Junction Connector
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to D-CAN Junction Connector)
    Wiring color 
    D-CAN Junction Connector
    Terminal No. (Symbol)
    Wiring Color
    Steering Sensor*1 (CAN-H)
    D42-1 (STR)
    SB
    Steering Sensor*1 (CAN-L)
    D42-12 (STR)
    W
    Yaw Rate Sensor*1 (CAN-H)
    D42-2 (YAW)
    BE
    Yaw Rate Sensor*1 (CAN-L)
    D42-13 (YAW)
    W
    DLC 3 (CAN-H)
    D42-3 (OBD)
    V
    DLC 3 (CAN-L)
    D42-14 (OBD)
    W
    Power steering ECU (CAN-H)
    D42-4 (EPS)
    SB
    Power steering ECU (CAN-L)
    D42-15 (EPS)
    W
    Main body ECU (CAN-H)
    D42-5 (JB)
    R
    Main body ECU (CAN-L)
    D42-16 (JB)
    W
    Combination meter ECU (CAN-H)
    D42-7 (MET)
    G
    Combination meter ECU (CAN-L)
    D42-18 (MET)
    W
    CAN Main wire (between D-CAN Junction Connector and P-CAN Junction Connector (CAN-H))
    D42-11 (TOLH)
    Y
    CAN Main wire (between D-CAN Junction Connector and P-CAN Junction Connector (CAN-L))
    D42-22 (TOLH)
    W

    1. *1: w/ VSC



  2. E191937E03
  3. P-CAN Junction Connector
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to P-CAN Junction Connector)
    Wiring color 
    P-CAN Junction Connector
    Terminal No. (Symbol)
    Wiring Color
    Skid Control ECU)*1 (CAN-H)
    D41-1 (ABS)
    G
    Skid Control ECU)*1 (CAN-L)
    D41-12 (ABS)
    W
    ECM (CAN-H)
    D41-4 (EFI)
    L
    ECM (CAN-L)
    D41-15 (EFI)
    W
    Air Conditioning Amplifier*2 (TX+)
    D41-6 (A/C)
    V
    Air Conditioning Amplifier*2 (TX-)
    D41-17 (A/C)
    W
    Center Airbag Sensor Assembly (CAN-H)
    D41-8 (A/B)
    B
    Center Airbag Sensor Assembly (CAN-L)
    D41-19 (A/B)
    W
    CAN Main Wire (between P-CAN Junction Connector and D-CAN Junction Connector (CAN-H))
    D41-11 (TORH)
    Y
    CAN Main Wire (between P-CAN Junction Connector and D-CAN Junction Connector (CAN-L))
    D41-22 (TORH)
    W

    1. *1: w/ ABS or VSC
    2. *2: w/ Air Conditioning



  4. Wiring diagram for identifying CAN junction connectors


    E191969E01


DLC3
E191939E13
  1. Turn the ignition switch off.

  2. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D15-6 (CANH) - D15-14 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    D15-6 (CANH) - D15-4 (CG)
    V - W-B
    Ignition switch off
    200 Ω or higher
    D15-14 (CANL) - D15-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D15-6 (CANH) - D15-16 (BAT)
    V - SB
    Ignition switch off
    6 kΩ or higher
    D15-14 (CANL) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher


BRAKE ACTUATOR (SKID CONTROL ECU)
E191940E30

HINT:
For vehicle with ABS only.

  1. Turn the ignition switch off.

  2. Disconnect the A76 brake actuator (skid control ECU) connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator (Skid Control ECU))

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A76-25 (CANH) - A76-14 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    A76-25 (CANH) - A76-1 (GND1)
    G - W-B
    Ignition switch off
    200 Ω or higher
    A76-14 (CANL) - A76-1 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A76-25 (CANH) - A76-12 (+BS)
    G - W
    Ignition switch off
    6 kΩ or higher
    A76-14(CANL) - A76-12 (+BS)
    W - W
    Ignition switch off
    6 kΩ or higher


ABS AND TRACTION ACTUATOR (SKID CONTROL ECU)
E191940E33

HINT:
For vehicle with VSC only.

  1. Turn the ignition switch off.

  2. Disconnect the A31 ABS and traction actuator (skid control ECU) connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ABS and Traction Actuator (Skid Control ECU))

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A31-25 (CANH) - A31-14 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    A31-25 (CANH) - A31-1 (GND1)
    G - W-B
    Ignition switch off
    200 Ω or higher
    A31-14 (CANL) - A31-1 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A31-25 (CANH) - A31-12 (+BS)
    G - W
    Ignition switch off
    6 kΩ or higher
    A31-14(CANL) - A31-12 (+BS)
    W - W
    Ignition switch off
    6 kΩ or higher


STEERING SENSOR
E191942E10

HINT:
For vehicle with VSC only.

  1. Turn the ignition switch off.

  2. Disconnect the D62 steering sensor connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Sensor)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D62-10 (CANH) - D62-9 (CANL)
    SB - W
    Ignition switch off
    54 to 69 Ω
    D62-10 (CANH) - D62-2 (ESS)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    D62-9 (CANL) - D62-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D62-10 (CANH) - D62-3 (BAT)
    SB - LG
    Ignition switch off
    6 kΩ or higher
    D62-9 (CANL) - D62-3 (BAT)
    W - LG
    Ignition switch off
    6 kΩ or higher


YAW RATE SENSOR
E191943E03

HINT:
For vehicle with VSC only.

  1. Turn the ignition switch off.

  2. Disconnect the D107 yaw rate sensor connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor)
    *b
    DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D107-3 (CANH) - D107-2 (CANL)
    BE - W
    Ignition switch off
    54 to 69 Ω
    D107-3 (CANH) - D15-4 (CG)
    BE - W-B
    Ignition switch off
    200 Ω or higher
    D107-2 (CANL) - D15-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D107-3 (CANH) - D15-16 (BAT)
    BE - SB
    Ignition switch off
    6 kΩ or higher
    D107-2 (CANL) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER
E191946E02

HINT:
For vehicle with manual air conditioning.

  1. Turn the ignition switch off.

  2. Disconnect the E8 air conditioning amplifier connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Air Conditioning Amplifier)
    *b
    DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    E8-2 (TX+) - E8-3 (TX-)
    V - W
    Ignition switch off
    54 to 69 Ω
    E8-2 (TX+) - E8-12 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    E8-3 (TX-) - E8-12 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E8-2 (TX+) - D15-16 (BAT)
    V - SB
    Ignition switch off
    6 kΩ or higher
    E8-3 (TX-) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher


ECM
E191944E03
  1. Turn the ignition switch off.

  2. Disconnect the A21 and C20 ECM connectors.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    A21-41 (CANH) - A21-49 (CANL)
    L - W
    Ignition switch off
    108 to 132 Ω
    A21-41 (CANH) - C20-104 (E1)
    L - W
    Ignition switch off
    200 Ω or higher
    A21-49 (CANL) - C20-104 (E1)
    W - W
    Ignition switch off
    200 Ω or higher
    A21-41 (CANH) - A21-20 (BATT)
    L - Y
    Ignition switch off
    6 kΩ or higher
    A21-49 (CANL) - A21-20 (BATT)
    W - Y
    Ignition switch off
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY
E191945E02
  1. Turn the ignition switch off.

  2. Disconnect the D16 center airbag sensor assembly connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    DLC3

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D16-13 (CANH) - D16-22 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    D16-13 (CANH) - D16-25 (E1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    D16-22 (CANL) - D16-25 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D16-13 (CANH) - D15-16 (BAT)
    B - SB
    Ignition switch off
    6 kΩ or higher
    D16-22 (CANL) - D15-16 (BAT)
    W - SB
    Ignition switch off
    6 kΩ or higher


POWER STEERING ECU
C118163E16
  1. Turn the ignition switch off.

  2. Disconnect the A19 and D31 power steering ECU connectors.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Steering ECU)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D31-1 (CANH) - D31-7 (CANL)
    SB - W
    Ignition switch off
    108 to 132 Ω
    D31-1 (CANH) - A19-2 (PGND)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    D31-7 (CANL) - A19-2 (PGND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D31-1 (CANH) - A19-1 (PIG)
    SB - W
    Ignition switch off
    6 kΩ or higher
    D31-7 (CANL) - A19-1 (PIG)
    W - W
    Ignition switch off
    6 kΩ or higher


COMBINATION METER ECU
E191947E18
  1. Turn the ignition switch off.

  2. Disconnect the D1 combination meter assembly connector.

  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter ECU)

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D1-20 (CANH) - D1-21 (CANL)
    G - W
    Ignition switch off
    54 to 69 Ω
    D1-20 (CANH) - D1-24 (ET)
    G - BR
    Ignition switch off
    200 Ω or higher
    D1-21 (CANL) - D1-24 (ET)
    W - BR
    Ignition switch off
    200 Ω or higher
    D1-20 (CANH) - D1-2 (ECUB)
    G - L
    Ignition switch off
    6 kΩ or higher
    D1-21 (CANL) - D1-2 (ECUB)
    W - L
    Ignition switch off
    6 kΩ or higher


MAIN BODY ECU

E114510E62


B108641E72

  1. Turn the ignition switch off.

  2. Disconnect the D33, 4B and 4E connectors.

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance 
    Terminal No. (Symbol)
    Wiring Color
    Switch Condition
    Specified Condition
    D33-23 (CANH) - D33-22 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D33-23 (CANH) - 4E-17 (GND1)
    R - W-B
    Ignition switch off
    200 Ω or higher
    D33-22 (CANL) - 4E-17 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D33-23 (CANH) - 4B-30 (BECU)
    R - L
    Ignition switch off
    6 kΩ or higher
    D33-22 (CANL) - 4B-30 (BECU)
    W - L
    Ignition switch off
    6 kΩ or higher