DTC P0130 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 1) |
DTC P2195 Oxygen Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen Sensor Signal Stuck Rich (Bank 1 Sensor 1) |


| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0130 | Voltage output of Heated Oxygen (HO2) sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm engine (2 trip detection logic) |
|
| P2195 | Output voltage of HO2 sensor remains at 0.5 V or less during idling with warm engine (2 trip detection logic) | |
| P2196 | Output voltage of HO2 sensor remains at 0.4 V or more during idling with warm engine (2 trip detection logic) |


| Case | Heated Oxygen Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0130, P2195 AND/OR P2196) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0130, P2195 and/or P2196 | A |
| P0130, P2195 and/or P2196 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 1)) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / O2S B1 S1.
Allow the engine to run for 90 seconds at 2,500 rpm.
Read the Heated Oxygen (HO2) sensor voltage while the engine is idling.

|
| ||||
| NG | |
| 3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C36 HO2 sensor (sensor 1) connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| HT1A (1) - +B (2) | 5.3 to 7.5 Ω at 20 °C (68°F) |
| HT1A (1) - E2 (4) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 4.INSPECT INTEGRATION NO.1 RELAY (EFI RELAY) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI fuse.
Remove the EFI fuse from the integration relay.
Check the EFI fuse resistance.
Reinstall the EFI fuse.
Inspect the EFI relay.
Check the EFI relay resistance.
| Tester Connections | Specified Conditions |
| 1C-1 - 1A-4 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1A-2 and 1A-3) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM) |
![]() ![]() |
Disconnect the C36 HO2 sensor (sensor 1) connector.
Disconnect the C20 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| OX1A (C36-3) - OX1A (C20-112) | Below 1 Ω |
| HT1A (C36-1) - HT1A (C20-109) |
| Tester Connections | Specified Conditions |
| OX1A (C36-3) or OX1A (C20-112) - Body ground | 10 kΩ or higher |
| HT1A (C36-1) or HT1A (C20-109) - Body ground |
Reconnect the HO2 sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leaks.
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 8.INSPECT FUEL INJECTOR |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).
|
| ||||
| OK | ||
| ||
| 9.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0130, P2195 AND/OR P2196) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC Output) | Proceed To |
| P0130, P2195 and/or P2196 | A |
| No output | B |
|
| ||||
| A | ||
| ||