Home › BODY ELECTRICAL › DOOR LOCK › KEY REMINDER WARNING SYSTEM

KEY REMINDER WARNING SYSTEM > Key Reminder Buzzer does not Sound

for Preparation Click here


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the main body ECU sends a key switch signal and driver side courtesy switch signal to the combination meter.

WIRING DIAGRAM


B117142E02


INSPECTION PROCEDURE

HINT:
Since the key reminder warning system has functions that use CAN communication, firstly confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with How to Proceed with Troubleshooting. Then, conduct the following troubleshooting procedure.

1.READ VALUE USING INTELLIGENT TESTER (KEY UNLOCK WARNING SW)
  1. Check the DATA LIST to ensure proper operation of the door unlock warning switch.

    Main Body ECU:

    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal / ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 4
OK


2.READ VALUE USING INTELLIGENT TESTER (D DOOR COURTESY SW)
  1. Check the DATA LIST to ensure proper operation of the front door courtesy light switch.

    Main Body ECU:

    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Driver side door courtesy switch signal / ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 6
OK


3.CHECK COMBINATION METER ASSEMBLY (WARNING BUZZER)
  1. Temporarily replace the combination meter assembly with a new or normally functioning one.

  1. Check the key reminder warning system function. (Click here)

    OK:
    The key reminder warning system functions properly.



NG
REPLACE MAIN BODY ECU
OK

END (COMBINATION METER ASSEMBLY IS FAULTY) 

4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY


    B117144E02
  1. Remove the unlock warning switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pushed
    10 kΩor higher
    1 - 2
    Pushed
    Below 1 Ω

  1. Reinstall the unlock warning switch assembly.



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY
OK


5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU)


    B121085E01
  1. Disconnect the D19 unlock warning switch connector.

  1. Disconnect the 4D main body ECU connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    D19-1 - 4D-7 (KSW)
    Below 1 Ω
    D19-1 or 4D-7 (KSW) - Body ground
    10 kΩor higher
    D19-2 - Body ground
    Below 1 Ω

  1. Reconnect the unlock warning switch and the main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

6.INSPECT FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE)


    B129185E01
  1. Remove the courtesy light switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Not pushed (ON)
    Below 1 Ω
    1 - Body ground
    Pushed (OFF)
    10 kΩor higher

  1. Reinstall the courtesy light switch.



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE)
OK


7.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH - MAIN BODY ECU)


    B112021E12
  1. LHD:

    1. Disconnect the J2 door courtesy switch connector.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      J2-1 - 4A-21 (DCTY)
      Below 1 Ω
      J2-1 or 4A-21 (DCTY) - Body ground
      10 kΩor higher

    4. Reconnect the courtesy switch and main body ECU connectors.

  1. RHD:

    1. Disconnect the J1 switch connector.

    2. Disconnect the 4A main body ECU connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      J1-1 - 4A-21 (DCTY)
      Below 1 Ω
      J1-1 or 4A-21 (DCTY) - Body ground
      10 kΩor higher

    4. Reconnect the courtesy switch and main body ECU connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU