Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the passenger side manual UP / DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B116305E04


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) (POWER SOURCE)


    B107969E21
  1. Disconnect the F1 or G7 power window regulator switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    LHD 
    Tester Connection
    Condition
    Specified Condition
    F1-3 - Body ground
    Ignition switch ON
    10 to 14 V
    RHD 
    Tester Connection
    Condition
    Specified Condition
    G7-3 - Body ground
    Ignition switch ON
    10 to 14 V

  1. Reconnect the power window regulator switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE)


    B107881
  1. Remove the power window regulator switch.

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 4
    2 - 1
    UP
    Below 1 Ω
    5 - 4
    2 - 1
    OFF
    Below 1 Ω
    5 - 4
    3 - 1
    DOWN
    Below 1 Ω

  1. Reinstall the power window regulator switch.



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE)
OK


3.CHECK HARNESS AND CONNECTOR (SWITCH (PASSENGER SIDE) - MOTOR (PASSENGER SIDE))


  1. Disconnect the F1 or G7 power window regulator switch connector.


    B111941E10

  1. Disconnect the F4 or G4 power window regulator motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD 
    Tester Connection
    Specified Condition
    F1-1 - F4-1
    Below 1 Ω
    F1-4 - F4-2
    Below 1 Ω
    F1-1 or F4-1 - Body ground
    10 kΩ or higher
    F1-4 or F4-2 - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    G7-1 - G4-1
    Below 1 Ω
    G7-4 - G4-2
    Below 1 Ω
    G7-1 or G4-1 - Body ground
    10 kΩ or higher
    G7-4 or G4-2 - Body ground
    10 kΩ or higher

  1. Reconnect the power window regulator switch connector.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE)


    B086400E01
  1. Remove the power window regulator motor.

  1. Apply the battery voltage to connector terminals 1 and 2.

    NOTICE:
    Do not apply the battery voltage to any terminals except terminals 1 and 2.

  1. Check that the motor gear rotates smoothly as follows.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise

  1. Reinstall the power window regulator motor.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE)
OK


5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (PASSENGER SIDE))


  1. Disconnect the G1 or F7 power window regulator master switch connector.


    B116290E03

  1. Disconnect the F1 or G7 power window regulator switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    w/o rear power window
    LHD 
    Tester Connection
    Specified Condition
    G1-16 (U) - F1-5
    Below 1 Ω
    G1-18 (D) - F1-2
    Below 1 Ω
    G1-16 (U) or F1-5 - Body ground
    10 kΩ or higher
    G1-18 (D) or F1-2 - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    F7-12 (U) - G7-5
    Below 1 Ω
    F7-10 (D) - G7-2
    Below 1 Ω
    F7-12 (U) or G7-5 - Body ground
    10 kΩ or higher
    F7-10 (D) or G7-2 - Body ground
    10 kΩ or higher
    w/ rear power window
    LHD 
    Tester Connection
    Specified Condition
    G1-16 (U) - F1-5
    Below 1 Ω
    G1-15 (D) - F1-2
    Below 1 Ω
    G1-16 (U) or F1-5 - Body ground
    10 kΩ or higher
    G1-15 (D) or F1-2 - Body ground
    10 kΩ or higher
    RHD 
    Tester Connection
    Specified Condition
    F7-12 (U) - G7-5
    Below 1 Ω
    F7-13 (D) - G7-2
    Below 1 Ω
    F7-12 (U) or G7-5 - Body ground
    10 kΩ or higher
    F7-13 (D) or G7-2 - Body ground
    10 kΩ or higher

  1. Reconnect the switch connectors.

  1. Reconnect the power window regulator motor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PASSENGER SWITCH)


  1. w/o rear power window:
    Inspect the passenger switch.



      B118051E05
    1. Remove the power window regulator master switch.



    2. B118052E04
    3. Measure the resistance of the switch when the switch is operated.

      Standard resistance:

      LHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      7 (E) - 18 (D)
      16 (U) - 15 (B)
      Below 1 Ω
      OFF
      OFF
      7 (E) - 16 (U)
      7 (E) - 18 (D)
      Below 1 Ω
      OFF
      DOWN
      7 (E) - 16 (U)
      15 (B) - 18 (D)
      Below 1 Ω
      ON
      UP
      7 (E) - 18 (D)
      10 kΩ or higher
      16 (U) - 15 (B)
      Below 1 Ω
      ON
      OFF
      16 (U) - 18 (D)
      Below 1 Ω
      ON
      DOWN
      7 (E) - 16 (U)
      10 kΩ or higher
      15 (B) - 18 (D)
      Below 1 Ω

      RHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      7 (E) - 10 (D)
      12 (U) - 15 (B)
      Below 1 Ω
      OFF
      OFF
      7 (E) - 12 (U)
      7 (E) - 10 (D)
      Below 1 Ω
      OFF
      DOWN
      7 (E) - 12 (U)
      15 (B) - 10 (D)
      Below 1 Ω
      ON
      UP
      7 (E) - 10 (D)
      10 kΩ or higher
      12 (U) - 15 (B)
      Below 1 Ω
      ON
      OFF
      12 (U) - 10 (D)
      Below 1 Ω
      ON
      DOWN
      7 (E) - 12 (U)
      10 kΩ or higher
      15 (B) - 10 (D)
      Below 1 Ω

    4. Reinstall the power window regulator master switch.



  1. w/ rear power window:
    Inspect the passenger switch.



      B107909E03
    1. Remove the power window regulator master switch.



    2. B107910E03
    3. Measure the resistance of the switch when the switch is operated.

      Standard resistance:

      LHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      1 (E) - 15 (D)
      6 (B) - 16 (U)
      Below 1 Ω
      OFF
      OFF
      1 (E) - 16 (U)
      1 (E) - 15 (D)
      Below 1 Ω
      OFF
      DOWN
      1 (E) - 16 (U)
      6 (B) - 15 (D)
      Below 1 Ω
      ON
      UP
      1 (E) - 15 (D)
      10 kΩ or higher
      6 (B) - 16 (U)
      Below 1 Ω
      ON
      OFF
      15 (D) - 16 (U)
      Below 1 Ω
      ON
      DOWN
      1 (E) - 15 (D)
      10 kΩ or higher
      6 (B) - 15 (D)
      Below 1 Ω

      RHD 
      Window Lock Switch Condition
      Power Window Switch Condition
      Tester Connection
      Specified Condition
      OFF
      UP
      9 (E) - 13 (D)
      6 (B) - 12 (U)
      Below 1 Ω
      OFF
      OFF
      9 (E) - 12 (U)
      9 (E) - 13 (D)
      Below 1 Ω
      OFF
      DOWN
      9 (E) - 12 (U)
      6 (B) - 13 (D)
      Below 1 Ω
      ON
      UP
      9 (E) - 13 (D)
      10 kΩ or higher
      6 (B) - 12 (U)
      Below 1 Ω
      ON
      OFF
      13 (D) - 12 (U)
      Below 1 Ω
      ON
      DOWN
      9 (E) - 12 (U)
      10 kΩ or higher
      6 (B) - 13 (D)
      Below 1 Ω

    4. Reinstall the power window regulator master switch.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL