Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > All Doors cannot be Locked / Unlocked Simultaneously

for Preparation Click here


DESCRIPTION

The main body ECU receives switch signals from the door control switch (for front driver door side), door control switch (for center console side*), driver side door key cylinder, front passenger side door key cylinder (w/o entry and start system) and front passenger side door lock switch, and activates the door lock motor on each door accordingly.
*: Hatchback

WIRING DIAGRAM


B146184E01


INSPECTION PROCEDURE

1.INSPECT FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE)


    B079551E10
  1. Apply the battery voltage to the door lock motor and measure the resistance.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (LSSR) - 7 (E)
    Battery positive (+) → Terminal 1 - Battery negative (-) → Terminal 4
    Below 1 Ω
    8 (LSSR) - 7 (E)
    Battery positive (+) → Terminal 4 - Battery negative (-) → Terminal 1
    10 kΩ or higher



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE)
OK


2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE))


    B145640E02
  1. Disconnect the D33 main body ECU connector.

  1. Disconnect the G5 door lock connector.

  1. Measure the resistance

    Standard resistance:
    Tester Connection
    Specified Condition
    D33-21 (LSWD) - G5-8 (LSSR)
    Below 1 Ω
    D33-21 (LSWD) or G5-8 (LSSR) - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the door lock connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK DOOR LOCK OPERATION
  1. Proceed to the next step according to the symptom listed in the table below.

    Result:

    Symptom
    Proceed to
    Doors cannot be locked using door control switch (for front driver door side)
    A
    Doors cannot be locked using driver side door key cylinder
    B
    Doors cannot be locked using door control switch (for center console side)*
    C
    Doors cannot be locked using front passenger side door key cylinder
    D

    *: Hatchback



B
Go to step 6

C
Go to step 8

D
Go to step 10
A


4.INSPECT DOOR CONTROL SWITCH (for Front Driver Door Side)
B108644E16
  1. LHD:

    1. Disconnect the G1 door control switch (for front driver door side) connector.

    2. Measure the resistance of the switch.

      Standard resistance (3 Door):
      Tester Connection
      Switch Condition
      Specified Condition
      1 (L) - 7 (E)
      Lock
      Below 1 Ω
      9 (UL) - 7 (E)
      Unlock
      Below 1 Ω
      1 (L) - 7 (E)
      OFF
      10 kΩ or higher
      9 (UL) - 7 (E)
      OFF
      10 kΩ or higher
      Standard resistance (5 Door and Sedan):
      Tester Connection
      Switch Condition
      Specified Condition
      2 (L) - 1 (E)
      Lock
      Below 1 Ω
      9 (UL) - 1 (E)
      Unlock
      Below 1 Ω
      2 (L) - 1 (E)
      OFF
      10 kΩ or higher
      9 (UL) - 1 (E)
      OFF
      10 kΩ or higher

    3. Reconnect the door control switch (for front driver door side) connector.



    B108644E17
  1. RHD:

    1. Disconnect the F7 door control switch (for front driver door side) connector.

    2. Measure the resistance of the switch.

      Standard resistance (3 Door):
      Tester Connection
      Switch Condition
      Specified Condition
      1 (L) - 7 (E)
      Lock
      Below 1 Ω
      9 (UL) - 7 (E)
      Unlock
      Below 1 Ω
      1 (L) - 7 (E)
      OFF
      10 kΩ or higher
      9 (UL) - 7 (E)
      OFF
      10 kΩ or higher
      Standard resistance (5 Door and Sedan):
      Tester Connection
      Switch Condition
      Specified Condition
      1 (L) - 9 (E)
      Lock
      Below 1 Ω
      8 (UL) - 9 (E)
      Unlock
      Below 1 Ω
      1 (L) - 9 (E)
      OFF
      10 kΩ or higher
      8 (UL) - 9 (E)
      OFF
      10 kΩ or higher

    3. Reconnect the door control switch (for front driver door side) connector.



NG
REPLACE DOOR CONTROL SWITCH (for Front Driver Door Side)
OK


5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH (Front Driver Door Side))
B123822E24
  1. LHD:

    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the G1 door control switch (for front driver door side) connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance (3 Door):
      Tester Connection
      Specified Condition
      4H-5 (UL1) - G1-9 (UL)
      Below 1 Ω
      4H-4 (L1) - G1-1 (L)
      Below 1 Ω
      4H-5 (UL1) or G1-9 (UL) - Body ground
      10 kΩ or higher
      4H-4 (L1) or G1-1 (L) - Body ground
      10 kΩ or higher
      Standard resistance (5 Door and Sedan):
      Tester Connection
      Specified Condition
      4H-5 (UL1) - G1-9 (UL)
      Below 1 Ω
      4H-4 (L1) - G1-2 (L)
      Below 1 Ω
      4H-5 (UL1) or G1-9 (UL) - Body ground
      10 kΩ or higher
      4H-4 (L1) or G1-2 (L) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the door control switch (for front driver door side) connector.



    B123822E25
  1. RHD:

    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the F7 door control switch (for front driver door side) connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance (3 Door):
      Tester Connection
      Specified Condition
      4H-5 (UL1) - F7-9 (UL)
      Below 1 Ω
      4H-4 (L1) - F7-1 (L)
      Below 1 Ω
      4H-5 (UL1) or F7-9 (UL) - Body ground
      10 kΩ or higher
      4H-4 (L1) or F7-1 (L) - Body ground
      10 kΩ or higher
      Standard resistance (5 Door and Sedan):
      Tester Connection
      Specified Condition
      4H-5 (UL1) - F7-8 (UL)
      Below 1 Ω
      4H-4 (L1) - F7-1 (L)
      Below 1 Ω
      4H-5 (UL1) or F7-8 (UL) - Body ground
      10 kΩ or higher
      4H-4 (L1) or F7-1 (L) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the door control switch (for front driver door side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

6.READ VALUE USING INTELLIGENT TESTER (DOR KEY SW-LOCK, DOR KEY SW-ULOCK)
  1. Check the DATA LIST to ensure the proper operation of the door lock and unlock switch.


Main Body ECU:

Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
Dor Key SW-Lock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to lock position
OFF: Driver side door key cylinder is turned to unlock position
-


Main Body ECU:

Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
Dor Key SW-ULock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to unlock position
OFF: Door key cylinder is turned to lock position
-

OK:
ON (driver side door key cylinder is turned to lock/unlock position) appears on tester screen.



OK
REPLACE MAIN BODY ECU
NG


7.CHECK HARNESS AND CONNECTOR (DRIVER SIDE DOOR LOCK ASSEMBLY - MAIN BODY ECU)
B123858E10
  1. LHD:

    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the G5 front door lock assembly connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      4H-6 (UL2) - G5-10 (UL)
      Below 1 Ω
      4H-7 (L2) - G5-9 (L)
      Below 1 Ω
      4H-6 (UL2) or G5-10(UL) - Body ground
      10 kΩ or higher
      4H-7 (L2) or G5-9 (L) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the front door lock assembly connector.



    B123858E11
  1. RHD:

    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the F5 front door lock assembly connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      4H-6 (UL2) - F5-5 (UL)
      Below 1 Ω
      4H-7 (L2) - F5-6 (L)
      Below 1 Ω
      4H-6 (UL2) or F5-5 (UL) - Body ground
      10 kΩ or higher
      4H-7 (L2) or F5-6 (L) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the front door lock assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

8.INSPECT DOOR CONTROL SWITCH (for Center Console Side)
B146555E01
  1. Disconnect the D30 door control switch (for center console side) connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    5 - 6
    Lock
    Below 1 Ω
    4 - 6
    Unlock
    Below 1 Ω
    5 - 6
    OFF
    Below 1 Ω
    4 - 6
    OFF
    Below 1 Ω

  1. Reconnect the door control switch (for center console side) connector.



NG
REPLACE DOOR CONTROL SWITCH (for Center Console Side)
OK


9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL SWITCH (Center Console Side))
B127311E02
  1. Disconnect the 4C and 4E main body ECU connectors.

  1. Disconnect the D30 door control switch (for center console side) connector.

  1. Measure the resistance of the fuses.

    Standard resistance:
    Tester Connection
    Specified Condition
    4C-10(UL1) - D30-4
    Below 1 Ω
    4E-11 (L1) - D30-5
    Below 1 Ω
    4C-10 (UL1) or D30-4 - Body ground
    10 kΩ or higher
    4E-11 (L1) or D30-5 - Body ground
    10 kΩ or higher

  1. Reconnect the main body ECU connector.

  1. Reconnect the door control switch (for center console side) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

10.READ VALUE USING INTELLIGENT TESTER (DOR KEY SW-LOCK, DOR KEY SW-ULCK)
  1. Check the DATA LIST to ensure the proper operation of the door lock and unlock switch.


Main Body ECU:

Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
Dor Key SW-Lock
Door key-linked lock switch signal/ ON or OFF
ON: Door key cylinder is turned to lock position
OFF: Driver side door key cylinder is turned to unlock position
-


Main Body ECU:

Item
Measurement Item/Display (Range)
Normal Condition
Diagnostic Note
Dor Key SW-ULck
Door key-linked unlock switch signal/ ON or OFF
ON: Door key cylinder is turned to unlock position
OFF: Door key cylinder is turned to lock position
-

OK:
ON (driver side door key cylinder is turned to lock/unlock position) appears on screen.



OK
REPLACE MAIN BODY ECU
NG


11.CHECK HARNESS AND CONNECTOR (PASSENGER SIDE DOOR LOCK ASSEMBLY - MAIN BODY ECU)
B123858E14
  1. LHD:

    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the F5 front door lock assembly connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      4H-15 (UL2) - F5-5 (UL)
      Below 1 Ω
      4H-16 (L2) - F5-6 (L)
      Below 1 Ω
      4H-15 (UL2) or F5-5 (UL) - Body ground
      10 kΩ or higher
      4H-16 (L2) or F5-6 (L) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the front door lock assembly connector.



    B123858E15
  1. RHD:

    1. Disconnect the 4H main body ECU connector.

    2. Disconnect the G5 front door lock assembly connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Tester Connection
      Specified Condition
      4H-15 (UL2) - G5-10 (UL)
      Below 1 Ω
      4H-16 (L2) - G5-9 (L)
      Below 1 Ω
      4H-15 (UL2) or G5-10(UL) - Body ground
      10 kΩ or higher
      4H-16 (L2) or G5-9 (L) - Body ground
      10 kΩ or higher

    4. Reconnect the main body ECU connector.

    5. Reconnect the front door lock assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU