Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit

for Preparation Click here


DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as to when a switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM


E170646E02


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).

1.INSPECT RADIO RECEIVER


    E141020E20
  1. Disconnect the D53 radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D53-7 (SW1) - D53-6 (SWG)
    No switch is pushed
    95 to 105 kΩ
    Seek+ switch: pushed
    Below 2.5 Ω
    Seek- switch: pushed
    312.5 to 345.5 Ω
    Volume+ switch: pushed
    950 to 1050 Ω
    Volume- switch: pushed
    2954.5 to 3265.5 Ω
    D53-8 (SW2) - D53-6 (SWG)
    No switch is pushed
    95 to 105 kΩ
    MODE switch: pushed
    Below 2.5 Ω
    Voice switch: pushed*1
    2954.5 to 3265.5 Ω
    On Hook switch: pushed*1
    312.5 to 345.5 Ω
    Off Hook switch: pushed*1
    950 to 1050 Ω

    *1: w/ Microphone

  1. Reconnect the radio receiver connector.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the V1 steering pad switch connector.



  1. Measure the resistance according to the value(s) in the table below.


    E170645E02


    Standard Resistance:

    Tester Connection
    Switch Condition
    Specified Condition
    V1-10 (AU1) - V1-8 (EAU)
    No switch is pushed
    95 to 105 kΩ
    Seek+ switch: pushed
    Below 2.5 Ω
    Seek- switch: pushed
    312.5 to 345.5 Ω
    Volume+ switch: pushed
    950 to 1050 Ω
    Volume- switch: pushed
    2954.5 to 3265.5 Ω
    V1-9 (AU2) - V1-8 (EAU)
    No switch is pushed
    95 to 105 kΩ
    MODE switch: pushed
    Below 2.5 Ω
    Voice switch: pushed*1
    2954.5 to 3265.5 Ω
    ON HOOK switch: pushed*1
    312.5 to 345.5 Ω
    OFF HOOK switch: pushed*1
    950 to 1050 Ω

    *1: w/ Microphone

  1. Reconnect the steering pad switch connector.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3.INSPECT SPIRAL CABLE


    E170601E02
  1. Disconnect the V1 steering pad switch connector.

  1. Disconnect the D3 spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V1-8 (EAU) - D3-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    V1-10 (AU1) - D3-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    V1-9 (AU2) - D3-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the precaution for the SRS (Click here).

  1. Reconnect the steering pad switch connector.

  1. Reconnect the spiral cable connector.



NG
REPLACE SPIRAL CABLE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR