Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER

B065593E10

  1. Disconnect the D24 amplifier connector.

  2. Measure the resistance of the wire harness side connector.

    Standard resistance: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    AGND (D24-7) - Body ground
    GR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the D24 amplifier connector.

  4. Measure the resistance and voltage of the connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    VC5 (D24-1) - AGND (D24-7)
    P- GR
    Power source
    1: No key in ignition key cylinder →
    2: Key inserted
    1: 0 V →
    2: 4.6 to 5.4 V
    CODE(D24-4) - AGND (D24-7)
    G- GR
    Demodulated signal of key code data
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 1)
    TXCT (D24-5) - AGND (D24-7)
    V- GR
    Key code output signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 2)
    AGND (D24-7) - Body ground
    GR- Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the amplifier.



  5. Inspect using an oscilloscope.



      B069240E03
    1. Waveform 1
      Terminal
      CODE - AGND
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      No key in ignition key cylinder →
      Key inserted



    2. B069239E03
    3. Waveform 2
      Terminal
      TXCT - AGND
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      No key in ignition key cylinder →
      Key inserted


CHECK TRANSPONDER KEY ECU ASSEMBLY

B085907E05

  1. Disconnect the D23 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Standard: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND (D23-16) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    AGND (D23-5) - Body ground
    GR - Body ground
    Ground for transponder key amplifier
    Always
    Below 1 Ω
    EGND (D23-11) - Body ground
    BR - Body ground
    Ground for ECM
    Always
    Below 1 Ω
    +B (D23-1) - GND (D23-16)
    L - W-B
    Battery
    Always
    11 to 14 V
    IG (D23-2) - AGND (D23-5)
    R - GR
    Ignition switch
    Ignition switch
    1: OFF →
    2: ON
    1: 0 V →
    2: 11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D23 ECU connector.

  4. Measure the voltage of the connector.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    KSW (D23-3) - GND (D23-16)
    O - W-B*1
    BE - W-B*2
    Unlock warning switch
    1: No key in ignition key cylinder →
    2: Key inserted
    1: 11 to 14 V→
    2: Below 1 V
    VC5 (D23-14) - AGND (D23-5)
    P - GR
    Power source
    1: No key in ignition key cylinder →
    2: Key inserted
    1: 0 V →
    2: 4.6 to 5.4 V
    TXCT (D23-4) - AGND (D23-5)
    V - GR
    Transponder key amplifier communication signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 1)
    CODE (D23-15) - AGND (D23-5)
    G - GR
    Transponder key amplifier communication signal
    No key in ignition key cylinder →
    Key inserted
    Pulse generation
    (see waveform 2)
    EFIO (D23-13) - GND (D23-16)
    W - W-B
    ECM output signal
    Ignition switch
    1: OFF →
    2: ON
    Pulse generation
    (see waveform 3)
    EFII (D23-12) - GND (D23-16)
    O - W-B*1
    BE - W-B*2
    ECM input signal
    Ignition switch
    1: OFF →
    2: ON
    Pulse generation
    (see waveform 4)
    CTY (D23-7) - GND (D23-16)
    B - W-B
    Courtesy signal
    1: Driver side door open →
    2: closed
    1: 11 to 14 V →
    2: Below 1 V
    IND (D23-8)- GND (D23-16)
    LG - W-B
    Security indicator signal
    Engine immobiliser system
    SET → UNSET
    1: 3 to 5 V →
    2: Below 1 V
    D (D23-9) - GND (D23-16)
    W - W-B
    Diagnosis tester communication
    Ignition switch ON
    Pulse generation

    1. *1: for Sedan
    2. *2: for Hatchback
    If the result is not as specified, there may be a malfunction in the ECU.



  5. Inspect using an oscilloscope.



      B069239E04
    1. Waveform 1
      Terminal
      TXCT - AGND
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Ignition switch
      1: OFF →
      2: ON



    2. B069240E03
    3. Waveform 2
      Terminal
      CODE - AGND
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Ignition switch
      1: OFF →
      2: ON



    4. B069241E01
    5. Waveform 3
      Terminal
      EFIO - GND
      Tool Setting
      10 V/DIV., 500 ms/DIV.
      Condition
      Ignition switch
      OFF → ON



    6. B069242E02
    7. Waveform 4
      Terminal
      EFII - GND
      Tool Setting
      10 V/DIV., 500 ms/DIV.
      Condition
      Ignition switch
      OFF → ON


CHECK ECM

B116297E16

  1. Disconnect the A21 ECM connector.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Standard voltage: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    IMI (A21-11) - E1 (C20-104)
    W - W
    Transponder key ECU input signal
    Ignition switch
    OFF → ON
    Pulse generation
    (see waveform 1)
    IMO (A21-10) - E1 (C20-104)
    O - W*1
    BE - W*2
    Transponder key ECU output signal
    Ignition switch
    OFF → ON
    Pulse generation
    (see waveform 2)
    E1 (C20-104) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω

    1. *1: for Sedan
    2. *2: for Hatchback
    If the result is not as specified, there may be a malfunction in the wire harness.



  3. Inspect using an oscilloscope.



      B069241E01
    1. Waveform 1
      Terminal
      IMI - E1
      Tool Setting
      10 V/DIV., 500 ms/DIV.
      Condition
      Ignition switch
      OFF → ON



    2. B069242E02
    3. Waveform 2
      Terminal
      IMO - E1
      Tool Setting
      10 V/DIV., 500 ms/DIV.
      Condition
      Ignition switch
      OFF → ON