Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to shorten labor time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON and push the intelligent tester main switch ON.

  3. On the intelligent tester, enter the following menu items: Body/Immobiliser/Data List.

    Transponder key ECU assembly 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key SW
    Unlock warning switch signal/
    ON or OFF
    OFF: No key is in ignition key cylinder
    ON: Key is in ignition key cylinder
    -
    IG SW
    Ignition switch signal/ ON or OFF
    OFF: Ignition switch OFF or ACC
    ON: Ignition switch ON
    -
    Immobiliser
    Immobiliser system status/
    SET or UNSET
    UNSET: Ignition switch ON
    SET: Without key
    -
    Permit (Start)
    Start control system starting control / OK or NG
    OK: Start control system starting is permitted
    NG: Start control system starting is not permitted
    -
    Response
    Transponder chip data/
    NG or OK
    NG: Data error
    OK: Data OK
    -
    Frame Error
    Transponder chip data/
    NG or OK
    NG: Data error
    OK: Data OK
    -
    Different Serial Number
    Transponder chip data/
    NG or OK
    NG: Data error
    OK: Data OK
    -
    Different Encrypt Code
    Transponder chip data/
    NG or OK
    NG: Data error
    OK: Data OK
    -
    Abnormal Status
    Transponder chip data/
    NG or OK
    NG: Data error
    OK: Data OK
    -
    Bcc Malfunction
    Transponder chip signal/
    NG or OK
    NG: Incorrect data sending
    OK: Correct data sending
    -
    Sub Key
    Sub-key code signal/
    NOMATCH or MATCH
    NOMATCH: Unmatched sub-key code is sent
    MATCH: Sub-key code is sent
    -
    Master Key
    Master key code signal/
    NOMATCH or MATCH
    NOMATCH: Unmatched master key code is sent
    MATCH: Master key code is sent
    -
    Transponda S-Code
    Number of registered sub-key/
    min. 0, max. 15
    Number of registered sub-keys
    -
    Transponda M-Code
    Number of registered master key/
    min. 0, max. 15
    Number of registered master keys
    -
    Reg Code Space Full
    Memory space for key
    codes registration/
    NOT FUL or FULL
    NOT FUL: Possible to register more key codes
    FULL: Cannot register any more key codes
    -
    +B
    +B judgment /
    NORMAL or BREAK
    NORMAL: Battery supply is normal
    BREAK: Battery supply is malfunctioning
    -
    Antenna Coil Status
    Transponder key coil condition/
    NORMAL or FAIL
    NORMAL: Transponder key coil is normal
    FAIL: Transponder key coil is malfunctioning
    -


ACTIVE TEST

HINT:
Performing the intelligent tester ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON and push the intelligent tester main switch ON.

  3. On the intelligent tester, enter the following menus: Body/Immobiliser/Active Test.

    Transponder key ECU assembly 
    Tester Display
    Test Part
    Control Range
    Security Indic
    Turn security indicator ON/OFF
    -